Yealink SIP-T33P Administrator's Guide

Phone Provisioning
90
PIN Code Provisioning Settings Configuration
You can enable the users to trigger phones to perform provisioning by dialing a PIN code.
For more information on PIN code provisioning, refer to Yealink SIP IP Phones Auto Provisioning Guide.
The following table lists the parameters you can use to configure settings for PIN code provisioning.
Parameter
phone_setting.retain_pin.enable <y0000000000xx>.cfg
Description
It enables or disables the phone to save the entered PIN code.
Permitted
Values
0-Disabled
1-Enabled, the phone saves the entered PIN code and users do not need to enter again.
Default
1
Supported
Devices
T57W, T54W, T53W, T53, T48U, T46U, T43U, T42U, T48S, T46S, T42S, T41S, T33P, T33G, T31P,
T31G, T31, T30P, T30, T27G and CP920
Viewing Configurations Configured via Different Provisioning Methods
On the web user interface, you can click the question mark "?" after each configuration to see its detailed inform-
ation. It is only applicable to T57W/T54W/T53W/T53/T48U/T48S/T46U/T46S/T43U/T42S/T42U/T41S/T27G/CP920
phones.
From the detailed information, you can do the following:
l Check whether settings you make using a higher priority provisioning method override settings made using a
lower priority provisioning method.
l Reset a configuration to factory setting.
l See the default value of the desired configuration.
The table lists each parameter in the detailed information.
Parameter Description
Description
Description of this configuration item
CFG Configuration
The parameter in the configuration file
Valid Value
The permitted values
Configuration Source Values
(This appears only when the para-
meter “static.auto_pro-
vision.custom.protect” is set to 1.)
Web/Local:
(It appears only for a
non-static parameter.)
Not Applicable: the value is not changed via phone or
web user interface.
Specific value: the value is changed via phone or web
user interface. Click Reset to reset the value.
Config:
(It appears only for a
non-static parameter.)
Not Applicable: the parameter is not changed in the con-
figuration files.
Specific value: the parameter is changed in the con-
figuration files. Click Reset to reset the value.
Static:
(It appears only for a
static parameter)
Not Applicable: the parameter is not configured in any
provisioning method.
Specific value: the value is configured in any pro-
visioning method. Click Reset to reset the value.

Yealink SIP-T33P Specifications

General

Mounting	Desk/Wall
Handset type	Wired handset
Product type	IP Phone
Product color	Gray
Wall mountable	Yes
Operating system installed	Linux
Lines quantity	4 lines
Phonebook capacity	1000 entries
Number of VoIP accounts	4
Volume control	Buttons
Number of function keys	5
Display diagonal	2.4 \
Display resolution	320 x 240 pixels
Voice codecs	AGC, AJB, CNG, G.711a, G.711u, G.722, G.723.1, G.726, G.729, G.729A, PLC, VAD, iLBC
Security algorithms	AES, HTTPS
Ethernet LAN data rates	10, 100 Mbit/s
Ethernet LAN interface type	Fast Ethernet
RJ-9 ports quantity	1
Ethernet LAN (RJ-45) ports	2
Input frequency	50/60 Hz
AC adapter input voltage	100 - 240 V
Power consumption (typical)	3 W
Power consumption (Power over Ethernet (PoE))	5 W
Number of handles included	1 pc(s)
Operating temperature (T-T)	-10 - 50 °C
Operating relative humidity (H-H)	10 - 95 %

Weight and Dimensions

Depth	186 mm
Width	212 mm
Height	146 mm