Epygi QX series Administrator's Guide

QX5
QXFXO4/QXISDN4/QXE1T1/QXFXS24; (SW Version 6.0.x) 62
QXFXO4/QXISDN4/QXE1T1/QXFXS24 Manual II: Administrator’s Guide
10. Enable the Set Overall Calling Time Limit checkbox if the overall duration of the calls placed with the selected routing rule should be defined.
11. Enable the Set Tracing / Debug Options on This Rule checkbox, if the tracing/debug options should be defined.
12. Press Next.
13. Select the user or attendant extension from the Use Extension Settings drop down list that the call will be placed on.
14. Specify the Destination Host and Port Number, Username and Password if an IP or IP-PSTN call type has been selected. For the IP-PSTN call type,
enable Multiple Logons if necessary. Enable the Use RTP Proxy checkbox if needed.
15. Choose the Authentication and Accounting method from the AAA Required drop down list.
16. Choose a Fail Reason from the corresponding drop down list.
17. Configure Transport Protocol for SIP messages and SIP Privacy parameters as needed.
18. Press the Next button.
19. If the Filter on Source / Modify Caller ID checkbox has been previously enabled and the destination type is different from the FXO, fill in the Source
Number Pattern into the corresponding text field. Choose the needed value from the Source Type drop down list, as well as the Number of
Discarded Symbols and Prefix values.
20. Press the Next button.
21. If IP has been selected on the previous step in the Source Type drop down list, then Source Host should be inserted in the current page. If FXO,
ISDN or E1/T1 has been selected in the Source Type drop down list, then the ISDN/E1T1 trunk or the FXO line number should be selected here.
22. If the Set Date/Time Period(s) checkbox has been selected on the first page, pressing Next will open the Date/Time Rules page where route
validity should be defined.
23. If the Set Overall Calling Time Limit checkbox has been selected on the first page, pressing Next will open the Routing Overall Calls Limitation
Settings page where the total call duration for all calls can be configured over a specific time frame for each Call Routing Entry.
24. If the Set Tracing / Debug Options on This Rule checkbox has been selected on the first page, pressing Next will open the Tracing/ Debug
Options page where the tracing/debug options should be defined.
25. Press the Finish button to establish a local route with the inserted settings.
To create a local AAA entry
1. Click on the Local AAA Table tab on the Call Routing page.
2. Press the Add button on the Local AAA Table page.
3. Choose the Authentication type.
4. Enter the Phone Number, Username and Password or the Authentication by PIN depending on the selected Authentication type.
5. Use the Expiration Date and Time checkbox to enable the expiration timeout.
6. Select the Expiration Date and Time from the corresponding drop down lists.
7. Press Save to apply these settings.
Allowed Characters and Wildcards
The following is the set of characters and wildcards allowed in the Pattern and Source Number Pattern text fields of the Call Routing Wizard:
Characters:
0…9
A…Z
a…z
+ = $ ; / ~ _ - . & ( ) ' ! * ? {} , [ ]
Please Note: The symbols * and ? should be prefixed with a slash (\) if they are used as ordinary characters; otherwise the system will interpret
them as wildcards.
Please Note: The symbols !, {, }, [, ], - and , are used to define a range of characters and cannot be used as ordinary characters.
Wildcards:
* Any number of any characters
? Any single character
{ } A character or a string from the specified set of characters and strings.
The following control symbols are used to specify a set:
• Use a comma (,) to separate the elements of a set.
Please Note: No spaces are allowed within braces.
Example:
The pattern is 9{1,3,11,a}.
Numbers matching the pattern are 91, 93 , 911, 9a.
• Use a minus sign (-) to specify a range of characters. Each successive element of the range is obtained by increasing the previous
element (the element code) by one.
Example:
The pattern is 2{11-15,a-d}5.
Numbers matching the pattern are 2115, 2125, 2135, 2145, 2155, 2a5, 2b5, 2c5, 2d5.

Epygi QX series Specifications

General

Brand	Epygi
Model	QX series
Category	PBX
Language	English