Keithley 2611B Reference Manual

Section
5: Introduction to TSP operation Series 2600B System SourceMeter® Instrument
Reference Manual
5-16 2600BS-901-01 Rev. B / May 2013
Triggering
The triggering commands allow you to set the conditions that the instrument uses to determine when
measurements are captured. See Sweep operation (on page 3-20
) for details on sweeping.
The digio and tsplink commands are not available on the Models 2604B, 2614B, and 2634B
digio.trigger[N].assert() (on page 7-51)
digio.trigger[N].clear() (on page 7-51)
digio.trigger[N].EVENT_ID (on page 7-52)
digio.trigger[N].mode (on page 7-52)
digio.trigger[N].overrun (on page 7-54)
digio.trigger[N].pulsewidth (on page 7-54)
digio.trigger[N].release() (on page 7-55)
digio.trigger[N].reset() (on page 7-55)
digio.trigger[N].stimulus (on page 7-56)
digio.trigger[N].wait() (on page 7-58)
display.trigger.clear() (on page 7-79)
display.trigger.EVENT_ID (on page 7-79)
display.trigger.overrun (on page 7-79)
display.trigger.wait() (on page 7-80)
lan.trigger[N].assert() (on page 7-128)
lan.trigger[N].clear() (on page 7-129)
lan.trigger[N].connect() (on page 7-130)
lan.trigger[N].connected (on page 7-130)
lan.trigger[N].disconnect() (on page 7-131)
lan.trigger[N].EVENT_ID (on page 7-131)
lan.trigger[N].ipaddress (on page 7-132)
lan.trigger[N].mode (on page 7-133)
lan.trigger[N].overrun (on page 7-134)
lan.trigger[N].protocol (on page 7-134)
lan.trigger[N].pseudostate (on page 7-135)
lan.trigger[N].stimulus (on page 7-135)
lan.trigger[N].wait() (on page 7-137)
smuX.trigger.arm.count (on page 7-232)
smuX.trigger.arm.set() (on page 7-233)
smuX.trigger.arm.stimulus (on page 7-233)
smuX.trigger.ARMED_EVENT_ID (on page 7-235)
smuX.trigger.autoclear (on page 7-235)
smuX.trigger.count (on page 7-236)
smuX.trigger.endpulse.action (on page 7-236)
smuX.trigger.endpulse.set() (on page 7-237)
smuX.trigger.endpulse.stimulus (on page 7-237)
smuX.trigger.endsweep.action (on page 7-239)
smuX.trigger.IDLE_EVENT_ID (on page 7-239)
smuX.trigger.initiate() (on page 7-240)
smuX.trigger.measure.action (on page 7-241)
smuX.trigger.measure.set() (on page 7-241)
smuX.trigger.measure.stimulus (on page 7-242)
smuX.trigger.measure.Y() (on page 7-244)
smuX.trigger.MEASURE_COMPLETE_EVENT_ID (on page 7-244)
smuX.trigger.PULSE_COMPLETE_EVENT_ID (on page 7-245)
smuX.trigger.source.action (on page 7-246)
smuX.trigger.source.limitY (on page 7-247)
smuX.trigger.source.linearY() (on page 7-248)
smuX.trigger.source.listY() (on page 7-249)
smuX.trigger.source.logY() (on page 7-250)

Keithley 2611B Specifications

General

Brand	Keithley
Model	2611B
Category	Measuring Instruments
Language	English