Keithley 3720-ST User Manual

Section 9: Introduction to TSP operation Series 3700A System Switch/Multimeter Reference Manual
9-36 3700AS-901-01 Rev. D/June 2018
Triggering
The triggering commands allow you to set the conditions that the instrument uses to determine when
measurements are captured.
digio.trigger[N].assert() (on page 11-116)
digio.trigger[N].clear() (on page 11-117)
digio.trigger[N].EVENT_ID (on page 11-117)
digio.trigger[N].mode (on page 11-118)
digio.trigger[N].overrun (on page 11-119)
digio.trigger[N].pulsewidth (on page 11-120)
digio.trigger[N].release() (on page 11-121)
digio.trigger[N].reset() (on page 11-121)
digio.trigger[N].stimulus (on page 11-122)
digio.trigger[N].wait() (on page 11-124)
display.trigger.EVENT_ID (on page 11-142)
lan.trigger[N].assert() (on page 11-273)
lan.trigger[N].clear() (on page 11-273)
lan.trigger[N].connect() (on page 11-274)
lan.trigger[N].connected (on page 11-275)
lan.trigger[N].disconnect() (on page 11-276)
lan.trigger[N].EVENT_ID (on page 11-276)
lan.trigger[N].ipaddress (on page 11-277)
lan.trigger[N].mode (on page 11-277)
lan.trigger[N].overrun (on page 11-278)
lan.trigger[N].protocol (on page 11-279)
lan.trigger[N].pseudostate (on page 11-280)
lan.trigger[N].stimulus (on page 11-280)
lan.trigger[N].wait() (on page 11-282)
trigger.blender[N].clear() (on page 11-406)
trigger.blender[N].EVENT_ID (on page 11-406)
trigger.blender[N].orenable (on page 11-407)
trigger.blender[N].overrun (on page 11-407)
trigger.blender[N].reset() (on page 11-408)
trigger.blender[N].stimulus[M] (on page 11-409)
trigger.blender[N].wait() (on page 11-410)
trigger.clear() (on page 11-411)
trigger.EVENT_ID (on page 11-411)
trigger.timer[N].clear() (on page 11-412)
trigger.timer[N].count (on page 11-412)
trigger.timer[N].delay (on page 11-413)
trigger.timer[N].delaylist (on page 11-414)
trigger.timer[N].EVENT_ID (on page 11-415)
trigger.timer[N].overrun (on page 11-415)
trigger.timer[N].passthrough (on page 11-416)
trigger.timer[N].reset() (on page 11-416)
trigger.timer[N].stimulus (on page 11-417)
trigger.timer[N].wait() (on page 11-419)
trigger.wait() (on page 11-419)
tsplink.trigger[N].assert() (on page 11-424)
tsplink.trigger[N].clear() (on page 11-425)
tsplink.trigger[N].EVENT_ID (on page 11-425)
tsplink.trigger[N].mode (on page 11-426)
tsplink.trigger[N].overrun (on page 11-427)
tsplink.trigger[N].pulsewidth (on page 11-428)
tsplink.trigger[N].release() (on page 11-428)
tsplink.trigger[N].reset() (on page 11-429)
tsplink.trigger[N].stimulus (on page 11-430)
tsplink.trigger[N].wait() (on page 11-431)

Keithley 3720-ST Specifications

General

Brand	Keithley
Model	3720-ST
Category	Multimeter
Language	English