65NIBE F1330
Control
Menu 6.9.2 Room balancingsystem [U]
Here you select which heating system the room sensor shall
affect. Can be set to Off, Heating syst1, Heating syst2 or
Heating sys 1&2. The factory setting is Off.
Menu 6.9.3 Desired room temperature [U]
The menu is only displayed if RG05 is selected in menu
9.1.11. The value can be adjusted between 10 and 30 °C
in increments of 0.5 °C. Factory setting is 20 °C.
Menu 6.9.4 Return [U]
Pressing the Enter button returns you to menu 6.9.0
Menu 6.10 Return [U]
Pressing the Enter button returns you to menu 6.0.
7.0 Clock
Menu 7.1 Date [N]
The current date is set here.
Menu 7.2 Time [N]
The current time is set here.
Menu 7.3.0 Temp set back time 1 [U]
Pressing the enter button takes you to sub-menus for day
changes period 1, where settings for night reduction are
located.
Menu 7.3.1 Temp set back time 1 [U]
Here you which heating system is to be influenced by day
changes period 1. When heating system 2 is installed both
System 1 and 2 can be selected. Can also be set to Off.
The factory setting is Off.
Menu 7.3.2 Offset heating curve [U]
Changes to the flow temperature with a day change, e.g.
the night reduction is set here. The value is adjustable be-
tween -10 and +10. The factory setting is 0.
Menu 7.3.3–7.3.9 Set Time Monday–Sunday [U]
The time for the day change, e.g. night reduction, is
chosen here.
Menu 7.3.10 Return [U]
Pressing the enter button returns you to menu 7.3.0.
Menu 7.4.0 Temp set back time 2 [U]
Pressing the enter button takes you to sub-menus for day
changes period 2, where settings for night reduction are
located.
Menu 7.4.1 Temp set back time 2 [U]
Here you which heating system is to be influenced by day
changes period 1. When heating system 2 is installed both
System 2 and 2 can be selected. Can also be set to Off. The
factory setting is Off.
Menu 7.4.2 Offset heating curve [U]
Changes to the flow temperature with a day change, e.g.
the night reduction is set here. The value is adjustable be-
tween -10 and +10. The factory setting is 0.
Menu 7.4.3–7.4.9 Set Time Monday–Sunday [U]
The time for the day change, e.g. night reduction is chosen
here.
Menu 7.4.10 Return [U]
Pressing the enter button returns you to menu 7.4.0.
Menu 7.5.0 Timer Extra Hotwater [U]
Pressing the enter button takes you to sub-menus for the
Extra hot water time settings. Settings are included here
when you wish to have Extra hot water on a specific day.
Menu 7.5.1 Timer Extra Hotwater [U]
You select here whether the time settings for Extra hot wa-
ter are to be On or Off. The factory setting is Off.
Menu 7.5.2 - 7.5.8 Extra HW Monday - Sunday [U]
The period for respective days when Extra hot water is to
be active is selected here. Hours and minutes for both start
and stop are shown The same start and stop times deacti-
vates Extra hot water.
Menu 7.5.9 Return [U]
Pressing the enter button returns you to menu 7.5.0.
Menu 7.6 Return [N]
Pressing the Enter button returns you to menu 7.0.
8.0 Other settings
Menu 8.1.0 Display settings [N]
Pressing the enter button takes you to sub-menus for the
display settings, where settings concerning language and
menu types are made.
Menu 8.1.1 Menu type [N]
The menu type is chosen here: Normal, extended or service.
[N] Normal, the menus the user needs for a quick produc-
tion control.
[U] Extended, shows all menus except the service menus.
[S] Service, shows all menus. Returns to the previous set-
ting 30 minutes after the last button was pressed.
The factory setting is Normal.
Menu 8.1.2 Language [N]
The menu language is selected here. The factory setting is
English.
Menu 8.1.3 Display contrast [N]
The display’s contrast is set here. The value is adjustable
between 0 and 31.
Menu 8.1.4 Light intensity [N]
The light intensity in screen saver mode is set here. Can be
set to Off, Low or Mid. Screen saver mode starts 30 min-
utes after the last button was pushed.
Menu 8.1.5 Return [N]
Pressing the enter button returns you to menu 8.1.0.
To Next Page
Loading...
Need help?
General
