SARA-R4/N4 series-AT Commands Manual
UBX-17003787 - R09

Contents
Page 7 of 307
7.11Read RSRQ values +VZWRSRQ................................................................................................................. 56
7.12eDRX setting +CEDRXS...............................................................................................................................57
7.13eDRX read dynamic parameters +CEDRXRDP....................................................................................... 58
7.14Set MNO profile +UMNOPROF.................................................................................................................. 59
7.15Band selection bitmask +UBANDMASK.................................................................................................. 60
8î™–î™–î™–î™–Security.............................................................................................................................. 62
8.1Enter PIN +CPIN..............................................................................................................................................62
8.2Facility lock +CLCK........................................................................................................................................63
8.3Change password +CPWD........................................................................................................................... 64
9î™–î™–î™–î™–Short Messages Service............................................................................................... 66
9.1Introduction......................................................................................................................................................66
9.2Select message service +CSMS................................................................................................................. 66
9.3Preferred message storage +CPMS...........................................................................................................67
9.4Preferred message format +CMGF............................................................................................................68
9.5Save settings +CSAS.................................................................................................................................... 69
9.6Restore settings +CRES...............................................................................................................................69
9.7New message indication +CNMI................................................................................................................. 70
9.8Read message +CMGR................................................................................................................................. 73
9.9New message acknowledgement to MT +CNMA....................................................................................75
9.10List message +CMGL.................................................................................................................................. 76
9.11Send message +CMGS.................................................................................................................................79
9.12Write message to memory +CMGW........................................................................................................ 80
9.13Send message from storage +CMSS....................................................................................................... 81
9.14Set text mode parameters +CSMP...........................................................................................................81
9.15Delete message +CMGD............................................................................................................................. 82
9.16Service center address +CSCA..................................................................................................................83
9.17Read concatenated message +UCMGR...................................................................................................84
9.18List concatenated message +UCMGL.....................................................................................................86
9.19Send concatenated message +UCMGS...................................................................................................89
9.20Write concatenated message to memory +UCMGW...........................................................................90
9.21More messages to send +CMMS...............................................................................................................91
9.22Sending of originating data via the control plane +CSODCP.............................................................. 91
9.23Terminating data reporting via control plane +CRTDCP.....................................................................92
10î™–î™–î™–î™–V24 control and V25ter............................................................................................... 94
10.1Introduction.................................................................................................................................................... 94
10.2Circuit 109 behavior &C............................................................................................................................... 94
10.3Circuit 108/2 behavior &D........................................................................................................................... 94
10.4DSR override &S........................................................................................................................................... 96
10.5Flow control &K.............................................................................................................................................96
10.6DTE-DCE character framing +ICF.............................................................................................................98
10.7DTE-DCE local flow control +IFC............................................................................................................... 99
10.8Set flow control \Q..................................................................................................................................... 100
10.9UART data rate configuration +IPR.........................................................................................................101
10.10Return to on-line data state O............................................................................................................... 102
10.11Escape character S2................................................................................................................................. 102
10.12Command line termination character S3.............................................................................................103
10.13Response formatting character S4.......................................................................................................104
10.14Command line editing character S5......................................................................................................104
10.15Pause before blind dialling S6................................................................................................................ 105
10.16Connection completion timeout S7.......................................................................................................105
10.17Command dial modifier time S8............................................................................................................ 106
10.18Automatic disconnect delay S10............................................................................................................106
10.19Escape prompt delay (EPD) S12............................................................................................................. 107
10.20Command echo E......................................................................................................................................107
10.21Result code suppression Q..................................................................................................................... 108
10.22DCE response format V.......................................................................................................................... 108
10.23Result code selection and call progress monitoring control X........................................................ 109
10.24Reset to default configuration Z...........................................................................................................109
To Next Page
Loading...
Need help?
General
