Name: GE Venue Go
Brand: GE
Rating: 4 (1 reviews)

To Next Page

To Previous Page

IRECTION 5813707-100, REVISION 2 VENUE GO™ SERVICE MANUAL

1-26 Chapter 1 - Introduction

PRELIMINARY

1-7-3 Venue Go™ Cart Labels Location

In addition to the labels described in the previous section, an additional label may be found on the

Venue Go™ cart, as described in the following section.

Figure 1-6 Venue Go™ System - Cart Labels Location

Table of Contents3
Overview27
- Purpose of Chapter 127
Service Manual Overview28
- Contents in this Service Manual28
- Venue Go™ Models Covered in this Manual29
- Product Description30
Important Conventions32
- Conventions Used in this Manual32
- Standard Hazard Icons33
Safety Considerations35
- Introduction35
- Human Safety35
- Mechanical Safety38
- Electrical Safety40
- Venue Go™ Battery Safety43
- Patient Data Safety43
Dangerous Procedure Warnings44
Lockout/Tagout (LOTO) Requirements45
Product Labels and Icons46
- Universal Product Labels46
- Label Descriptions47
- Venue Go™ Cart Labels Location52
Returning/Shipping Probes and Repair Parts53
EMC, EMI, and ESD54
- Electromagnetic Compatibility (EMC)54
- Peripherals Used in the Patient Environment54
- Compliance55
- Electrostatic Discharge (ESD) Prevention56
- General Caution56
Direction 5813707-100, Revision57
- Contact Information57
Customer Assistance57
Overview59
- Purpose of Chapter 259
Console Requirements60
- Unit Environmental Requirements60
- Cooling Requirements60
- Lighting Requirements60
- Time and Manpower Requirements60
- Electrical Requirements61
- EMI Limitations62
- EMI Prevention/Abatement63
- Probe Environmental Requirements63
- Time and Manpower Requirements64
Facility Needs65
- Purchaser Responsibilities65
- Required Facility Needs66
- Networking Pre-Installation Requirements70
Connectivity Installation Worksheet71
Overview75
- Purpose of Chapter 375
Setup Reminders76
- Average Setup Time76
- Setup Warnings76
- Safety Reminders77
Receiving and Unpacking the Equipment78
- Warnings for Receiving and Unpacking the Equipment78
- Overview78
- Unpacking Venue Go™ System79
- Unpacking Venue Go™ Cart81
- Physical Inspection84
- EMI Protection84
Preparing for Setup85
- Verifying Customer Order85
- Physical Inspection85
- Component Inspection85
- Irection Revision Enue Ervice Anual86
Completing the Setup89
- System Specifications89
- Electrical Specifications90
- Connections on the I/O Rear Panel90
- Connecting Probes90
- Power On/Boot up93
- Power Shut down93
- Complete Power down93
Configuration94
- Purpose of this Section94
- Venue Go™ Configuration94
- Service Screen Setup106
- Optional Peripherals/Peripheral Connection107
- Software Options Configuration110
Connectivity Overview111
- Physical Connection111
- Stand-Alone Venue Go111
- Wired Ethernet from Venue Go™ to a Workstation111
Connectivity Setup112
- Introduction112
- Select TCP/IP Screen113
- Changing the AE Title And/Or Port Number (Port No.)114
- Setup Connection to a DICOM Server114
Options Setup129
- Software Options129
- USB Flash Card Setup129
Paperwork after Setup130
- Installation Acceptance Test Criteria130
- User's Manual(S)130
- Product Locator Installation Card130
Overview139
- Purpose of Chapter 4139
General Procedures140
- Overview140
- Power On/Boot-Up141
- Power Shutdown143
- Logging on to the Venue Go™ as "ADM143
- Data Management144
- Deleting Patient Information145
- Transporting the Venue Go™ Ultrasound Scanner146
Functional and Safety Checks147
- Overview147
- Safety Checks148
- Phantoms Performance Checks148
- Image Quality Tests149
- Probe/Connectors Check155
- Peripheral Checks156
- Mechanical Functions Checks160
- Functionality Tests165
Overview166
- Purpose of Chapter 5166
General Information167
- Introduction167
- Venue Go™ Mechanical Design167
- 5813707-100, Revision167
Venue Go™ System Design169
- External Power Supply Section170
- Venue Go™ User Interface Components170
Venue Go™ Back End (C-BEB)172
- Back End172
Compact Front End Board (C-FEB)173
- General Information173
- C-FEB Interfaces173
- Probe Selection Board (C-PSB)175
Venue Go™ Display176
- General176
- Display Panel and Multi-Touch (MT)176
- Speaker178
External Input/Output179
System Power Distribution180
- Introduction180
System Monitoring181
- Power Management Controller182
- System Power Consumption182
- Rechargeable Battery Pack182
Cooling System185
- General Information185
Peripherals186
- Internal Peripheral186
- External Peripherals186
- Purpose of this Section187
- 5813707-100, Revision187
Connectivity187
- Venue Go™ and a DICOM Server in a Network187
Insite Exc188
- Introduction188
- Insite Exc Icon188
- Initiating a Request for Service (RFS)190
- Purpose of Chapter 6193
Service Safety Considerations195
Gathering Troubleshooting Data196
- Purpose of this Section196
- Collect Vital System Information196
- Collect a 'Trouble Image' with Logs197
Noise Troubleshooting199
- Purpose of this Section199
- Introduction199
- Overview of Types of Noise199
- Different Power Outlet201
- Different System201
- Different Location201
- Disconnect External Cables201
- Irection Revision Enue Ervice Anual201
Using a Loaner System During Faulty System Repair202
- Purpose of this Section202
- Transferring Data to the Loaner System202
Overview207
- Purpose of Chapter 8207
Internal Parts- Replacement Procedures208
- Preparations208
- Batteries Replacement Procedure209
- Back Cover Replacement Procedure211
- C-PSB Replacement Procedure214
- Probe Lever Replacement Procedure216
- Wifi Module Replacement Procedure219
- Fan Replacement Procedure222
- C-BEB and SSD Replacement Procedure226
- C-FEB Heat Sync Assembly Replacement Procedure231
- C-FEB Replacement Procedure234
- Front Display Assembly Replacement Procedure237
- Speakers Replacement Procedure239
- Cart bin Replacement Procedure242
- Mounting / Dismounting System on Cart243
- Cradle Assembly Replacement Procedure246
- Cradle Tilt Replacement Procedure248
- Casters Replacement Procedure251
- Printer Assembly Replacement Procedure252
- Printer and Printer Bracket Replacement Procedure254
- Cart Tray Replacement Procedure256
- Cart Up/Down Handle Replacement Procedure259
- ECG Replacement Procedure260
- Printer USB Cable Replacement Procedure262
- ECG USB Cable Replacement Procedure264
- AC/DC PSU and Split Cable Replacement Procedure266
Software Loading Procedures270
- Software Installation/Update Procedures - General Overview270
- Preparation and Notes for Software Upgrade Procedure271
- Software Installation Procedure272
- Software Reload/Update Procedure277
- Software Recovery Procedure284
Functional Checks to be Performed after Replacement Procedures288
- General Overview288
- Submitting a Replacement Procedure Report288
- Functional Checks Required Per Replacement Part Category288
Overview291
List of Abbreviations292
Venue-Go™ System on Cart Overview293
Renewal Parts Lists and Diagrams294
- Mechanical Hardware Parts294
- Covers295
- System Parts295
- Cart Parts298
- Probes300
- Software Media301
- System Power Cables302
- Peripherals304
Overview306
- Periodic Maintenance Inspections306
Warnings307
Why Perform Maintenance Procedures308
- Keeping Records308
- Quality Assurance308
- Maintenance Task Schedule308
Tools Required310
- Tools Required for Servicing the Venue Go310
System Maintenance311
- Preliminary Checks311
- Functional Checks312
- Physical Inspection314
- Cleaning315
Probe Maintenance317
- Probe Related Checks317
- Probe Handling317
- Basic Probe Care317
- Probe Cleaning318
- Returning and Shipping of Defective Probes319
Electrical Safety Tests320
- Overview320
- Outlet Test - Wiring Arrangement - USA and Canada322
- Grounding Continuity322

GE Venue Go Service Manual

Table of Contents

Questions and Answers:

GE Venue Go Specifications

Related product manuals

Brand	GE
Model	Venue Go
Category	Medical Equipment
Language	English