To Next Page

To Previous Page

IRECTION 5813707-100, REVISION 2 VENUE GO™ SERVICE MANUAL

Chapter 3 - System Setup 3-7

PRELIMINARY

3-3-4 Unpacking Venue Go™ Cart

1.) Open the box and identify the base protective foam.

2.) Remove the base protective foams, and expose the wheels.

CAUTION

Two people are needed to unpack the Venue Go cart because of its weight.

Two people are required whenever a part weighing 16 KG (35 LBS) or more must be lifted

Figure 3-5 Open the Cart Box

Figure 3-6 Remove Base Protective Foam

Table of Contents3
Overview27
- Purpose of Chapter 127
Service Manual Overview28
- Contents in this Service Manual28
- Venue Go™ Models Covered in this Manual29
- Product Description30
Important Conventions32
- Conventions Used in this Manual32
- Standard Hazard Icons33
Safety Considerations35
- Introduction35
- Human Safety35
- Mechanical Safety38
- Electrical Safety40
- Venue Go™ Battery Safety43
- Patient Data Safety43
Dangerous Procedure Warnings44
Lockout/Tagout (LOTO) Requirements45
Product Labels and Icons46
- Universal Product Labels46
- Label Descriptions47
- Venue Go™ Cart Labels Location52
Returning/Shipping Probes and Repair Parts53
EMC, EMI, and ESD54
- Electromagnetic Compatibility (EMC)54
- Peripherals Used in the Patient Environment54
- Compliance55
- Electrostatic Discharge (ESD) Prevention56
- General Caution56
Direction 5813707-100, Revision57
- Contact Information57
Customer Assistance57
Overview59
- Purpose of Chapter 259
Console Requirements60
- Unit Environmental Requirements60
- Cooling Requirements60
- Lighting Requirements60
- Time and Manpower Requirements60
- Electrical Requirements61
- EMI Limitations62
- EMI Prevention/Abatement63
- Probe Environmental Requirements63
- Time and Manpower Requirements64
Facility Needs65
- Purchaser Responsibilities65
- Required Facility Needs66
- Networking Pre-Installation Requirements70
Connectivity Installation Worksheet71
Overview75
- Purpose of Chapter 375
Setup Reminders76
- Average Setup Time76
- Setup Warnings76
- Safety Reminders77
Receiving and Unpacking the Equipment78
- Warnings for Receiving and Unpacking the Equipment78
- Overview78
- Unpacking Venue Go™ System79
- Unpacking Venue Go™ Cart81
- Physical Inspection84
- EMI Protection84
Preparing for Setup85
- Verifying Customer Order85
- Physical Inspection85
- Component Inspection85
- Irection Revision Enue Ervice Anual86
Completing the Setup89
- System Specifications89
- Electrical Specifications90
- Connections on the I/O Rear Panel90
- Connecting Probes90
- Power On/Boot up93
- Power Shut down93
- Complete Power down93
Configuration94
- Purpose of this Section94
- Venue Go™ Configuration94
- Service Screen Setup106
- Optional Peripherals/Peripheral Connection107
- Software Options Configuration110
Connectivity Overview111
- Physical Connection111
- Stand-Alone Venue Go111
- Wired Ethernet from Venue Go™ to a Workstation111
Connectivity Setup112
- Introduction112
- Select TCP/IP Screen113
- Changing the AE Title And/Or Port Number (Port No.)114
- Setup Connection to a DICOM Server114
Options Setup129
- Software Options129
- USB Flash Card Setup129
Paperwork after Setup130
- Installation Acceptance Test Criteria130
- User's Manual(S)130
- Product Locator Installation Card130
Overview139
- Purpose of Chapter 4139
General Procedures140
- Overview140
- Power On/Boot-Up141
- Power Shutdown143
- Logging on to the Venue Go™ as "ADM143
- Data Management144
- Deleting Patient Information145
- Transporting the Venue Go™ Ultrasound Scanner146
Functional and Safety Checks147
- Overview147
- Safety Checks148
- Phantoms Performance Checks148
- Image Quality Tests149
- Probe/Connectors Check155
- Peripheral Checks156
- Mechanical Functions Checks160
- Functionality Tests165
Overview166
- Purpose of Chapter 5166
General Information167
- Introduction167
- Venue Go™ Mechanical Design167
- 5813707-100, Revision167
Venue Go™ System Design169
- External Power Supply Section170
- Venue Go™ User Interface Components170
Venue Go™ Back End (C-BEB)172
- Back End172
Compact Front End Board (C-FEB)173
- General Information173
- C-FEB Interfaces173
- Probe Selection Board (C-PSB)175
Venue Go™ Display176
- General176
- Display Panel and Multi-Touch (MT)176
- Speaker178
External Input/Output179
System Power Distribution180
- Introduction180
System Monitoring181
- Power Management Controller182
- System Power Consumption182
- Rechargeable Battery Pack182
Cooling System185
- General Information185
Peripherals186
- Internal Peripheral186
- External Peripherals186
- Purpose of this Section187
- 5813707-100, Revision187
Connectivity187
- Venue Go™ and a DICOM Server in a Network187
Insite Exc188
- Introduction188
- Insite Exc Icon188
- Initiating a Request for Service (RFS)190
- Purpose of Chapter 6193
Service Safety Considerations195
Gathering Troubleshooting Data196
- Purpose of this Section196
- Collect Vital System Information196
- Collect a 'Trouble Image' with Logs197
Noise Troubleshooting199
- Purpose of this Section199
- Introduction199
- Overview of Types of Noise199
- Different Power Outlet201
- Different System201
- Different Location201
- Disconnect External Cables201
- Irection Revision Enue Ervice Anual201
Using a Loaner System During Faulty System Repair202
- Purpose of this Section202
- Transferring Data to the Loaner System202
Overview207
- Purpose of Chapter 8207
Internal Parts- Replacement Procedures208
- Preparations208
- Batteries Replacement Procedure209
- Back Cover Replacement Procedure211
- C-PSB Replacement Procedure214
- Probe Lever Replacement Procedure216
- Wifi Module Replacement Procedure219
- Fan Replacement Procedure222
- C-BEB and SSD Replacement Procedure226
- C-FEB Heat Sync Assembly Replacement Procedure231
- C-FEB Replacement Procedure234
- Front Display Assembly Replacement Procedure237
- Speakers Replacement Procedure239
- Cart bin Replacement Procedure242
- Mounting / Dismounting System on Cart243
- Cradle Assembly Replacement Procedure246
- Cradle Tilt Replacement Procedure248
- Casters Replacement Procedure251
- Printer Assembly Replacement Procedure252
- Printer and Printer Bracket Replacement Procedure254
- Cart Tray Replacement Procedure256
- Cart Up/Down Handle Replacement Procedure259
- ECG Replacement Procedure260
- Printer USB Cable Replacement Procedure262
- ECG USB Cable Replacement Procedure264
- AC/DC PSU and Split Cable Replacement Procedure266
Software Loading Procedures270
- Software Installation/Update Procedures - General Overview270
- Preparation and Notes for Software Upgrade Procedure271
- Software Installation Procedure272
- Software Reload/Update Procedure277
- Software Recovery Procedure284
Functional Checks to be Performed after Replacement Procedures288
- General Overview288
- Submitting a Replacement Procedure Report288
- Functional Checks Required Per Replacement Part Category288
Overview291
List of Abbreviations292
Venue-Go™ System on Cart Overview293
Renewal Parts Lists and Diagrams294
- Mechanical Hardware Parts294
- Covers295
- System Parts295
- Cart Parts298
- Probes300
- Software Media301
- System Power Cables302
- Peripherals304
Overview306
- Periodic Maintenance Inspections306
Warnings307
Why Perform Maintenance Procedures308
- Keeping Records308
- Quality Assurance308
- Maintenance Task Schedule308
Tools Required310
- Tools Required for Servicing the Venue Go310
System Maintenance311
- Preliminary Checks311
- Functional Checks312
- Physical Inspection314
- Cleaning315
Probe Maintenance317
- Probe Related Checks317
- Probe Handling317
- Basic Probe Care317
- Probe Cleaning318
- Returning and Shipping of Defective Probes319
Electrical Safety Tests320
- Overview320
- Outlet Test - Wiring Arrangement - USA and Canada322
- Grounding Continuity322

Brand	GE
Model	Venue Go
Category	Medical Equipment
Language	English

GE Venue Go Service Manual

Table of Contents

Questions and Answers:

GE Venue Go Specifications

Related product manuals