D9U001MCX-0101_03
20
Additional Instructions for Correct Use:
► Follow the instructions carefully.
► Use the bed exclusively if it is in perfect working order.
► If necessary, check the bed functions daily or at each shift change.
► Ensure any user has read and understood the instructions for use completely before operating the product.
► Use the bed exclusively with the correct mains supply.
► Ensure that the bed is operated exclusively by qualied personnel who have been trained according to the instructions for
use.
► Ensure that the patient (health permitting) has been informed about the operation of the bed and all applicable safety
instructions.
► Move the bed exclusively on even, hard-surfaced oors.
► Contact service department of the manufacturer immediately to let it replace any damaged parts by the original spare
parts.
► Ensure the bed is operated by qualified personnel trained in using the bed in accordance with the instructions for use by
manufacturer or by person approved by the manufacturer, eventually by authorized representative or by person approved by the
authorized representative.
► Ensure that maintenance and installation are performed exclusively by qualied personnel who have been trained by the
manufacturer.
► During peak loads or unavoidable excess loads (CPR), adjust Mattress support platform to the lowest position.
► Ensure that only one adult patient lies on the bed at any time.
► To avoid injury or crushing, take extra caution when operating any moving parts of the bed.
► When using lifting poles or infusion stands, ensure that nothing will be damaged when you move or adjust the bed.
► Brake the castors when the bed is occupied.
► Keep the Mattress support platform in the lowest position at any time when the healthcare personnel are not treating the
patient in order to prevent the patient from falling or injuries.
► Ensure that siderails are operated exclusively by healthcare personnel.
► Never use the bed in areas where there is a hazard of explosion.
► Enable or disable functions on Patient Control Panels using the Attendant Control Panel as appropriate for the patient’s
physical and mental state. Verify that the function is actually disabled.
► Never handle the mains plug with wet hands.
► Disconnect the product from the mains exclusively by pulling the mains plug.
► When pulling the mains plug, always hold the plug, not the cable.
► Position the mains cable so that there are no loops or kinks in the cable; protect the cable from mechanical wear and tear.
► Improper handling of mains cable can cause an electric shock hazard, other serious injuries or damage to the mattress
replacement system.
► Ensure that the stipulated duty cycle of motor is not exceeded.
► To change fuses or cables contact servise organisation authorized by manufacturer.
► To prevent failures, use exclusively the manufacturer’s original accessories and mattresses.
► Ensure that the stipulated safe working load is not exceeded.
► If the patient‘s condition could lead to an entrapment, leave the mattress support platform in the at position whilst una-
ttended.
► Adjust bed height when transporting the bed in order to facilitate overcoming possible obstacles.
► Do not exceed maximum load of 80 kg (176.37 lbs) for mattress support platform extension.
► Do not exceed the maximum patient weight limit (see Mechanical Specications).
► Do not hang anything on any cable.
► Never use the mattress replacement system near radiators or other heat sources.
► Select a suitable location for the placement of bed accessories and other objects to prevent involuntary activation of
buttons or controls which may result in the adjustment of bed positioning.
► Do not use the bed when its parts have been removed (e.g. parts of mattress support platform) unless these parts are
designed to be removed.
► Never place any accessories or handset on the siderails where keyboards are located.
► After each emergency situation always check if any of the controllers (controllers in siderails, handset or ACP) is not invo-
luntarily pressed by the bed accessories or by the mattress.
► The weighing system must be calibrated at regular intervals and in accordance with the metrological regulations of the
relevant country. All testing and certication must be carried out by qualied personnel. The healthcare provider is responsible for
ensuring the required testing frequency and testing procedure of the weighing system is carried out.
► To avoid unintended activation of moving parts during any use of the bed always check that none of the control elements
of the bed is pressed by persons, mattress or other objects.
► When adjusting the ALT (Automatic Lateral Therapy), ensure that the process does not pose any risk of the patient falling
or getting injured, or of any lines or tracheal tubes getting pulled out.
To Next Page
Loading...
Need help?
General
