Danfoss VLT AQUA FC 202 Design Guide

Displacement power factor (cos Φ)
Near unity (>0.98)
Switching on the input supply L1, L2, L3 (power-ups) ≤7.5 kW
Maximum 2 times per minute
Switching on input supply L1, L2, L3 (power-ups) 11–90 kW
Maximum 1 time per minute
Environment according to EN60664-1
Overvoltage category III/pollution degree 2
1
Mains voltage low/mains drop-out: During low mains voltage or a mains drop-out, the drive continues until the DC-link voltage drops below the
minimum stop level, which corresponds typically to 15% below the drive's lowest rated supply voltage. Power-up and full torque cannot be exptec-
ted at mains voltage lower than 10% below the drive's lowest rated supply voltage.
2
The unit is suitable for use on a circuit capable of delivering not more than 100000 RMS symmetrical Amperes, 240/500/600/690 V maximum.
3
The drive power supply is tested in accordance with IEC 61000-4-28, 50 Hz +4/-6%.
8.3 Motor Output and Motor Data
8.3.1 Motor Output (U, V, W)
Output voltage
0–100% of supply voltage
Output frequency
0–590 Hz
(1)
Switching on output
Unlimited
Ramp times
1–3600 s
1
Dependent on power size.
8.3.2 Torque Characteristics, Normal Overload
Starting torque (constant torque)
Maximum 110% for 60 s, once in 10 minutes
(1)
Overload torque (constant torque)
Maximum 110% for 60 s, once in 10 minutes
(1)
1
Percentage relates to the nominal torque of the drive, dependent on power size.
8.3.3 Torque Characteristics, High Overload
Starting torque (constant torque)
Maximum 150/160% for 60 s, once in 10 minutes
(1)
Overload torque (constant torque)
Maximum 150/160% for 60 s, once in 10 minutes
(1)
1
Percentage relates to the nominal torque of the drive, dependent on power size.
8.4 Ambient Conditions
8.4.1 Environment
Enclosure size A
IP20/Chassis, IP21/Type 1, IP55/Type 12, IP66/Type 4X
Enclosure sizes B1/B2
IP21/Type 1, IP55/Type 12, IP66/Type 4X
Enclosure sizes B3/B4
IP20/Chassis
Enclosure sizes C1/C2
IP21/Type 1, IP55/Type 12, IP66/Type 4X
Enclosure sizes C3/C4
IP20/Chassis
Enclosure kit available ≤ enclosure size A
IP21/TYPE 1/IP4X top
Vibration test enclosure A/B/C
1.0 g
Maximum relative humidty
5–95% (IEC 721-3-3); Class 3K3 (non-condensing) during opera-
tion
Aggressive environment (IEC 60068-2-43), uncoated
Class 3C2
Aggressive environment (IEC 60068-2-43), coated
Class 3C3
Test method according to IEC 60068-2-43
H2S (10 days)
Ambient temperature (at SFAVM switching mode)
- with derating
Maximum 55° C (131° F)
(1)
AJ300847815559en-000101 / 130R033790 | Danfoss A/S © 2020.09
Specications
VLT® AQUA Drive FC 202
Design Guide

Danfoss VLT AQUA FC 202 Specifications

General

Brand	Danfoss
Model	VLT AQUA FC 202
Category	DC Drives
Language	English