EasyManuals Logo
Home>FlexRadio>Transceiver>Signature FLEX-6000 Series

FlexRadio Signature FLEX-6000 Series User Manual

FlexRadio Signature FLEX-6000 Series
222 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #62 background imageLoading...
Page #62 background image
FLEX-6000 Signature Series Maestro User Guide
Copyright 2024 FlexRadio, Inc. All Rights Reserved. | Page 53
10 MAESTRO OVERVIEW
10.1 THEORY OF OPERATION
Maestro is a hardware and software system designed to operate FLEX-6000 Signature Series radios.
FLEX-6000 radios perform wide-band sampling of the RF spectrum. How is wide-band sampling
different from other radios?
In superheterodyne (also called “superhet” or “multiconversion”) radio systems, a series of down-
conversions using local oscillators is performed on the RF input ultimately resulting in a baseband
signal. This signal is generally only a few kilohertz wide and is ready to be demodulated and
presented to the operator in the form of audio. In a superheterodyne architecture, generally only a
single receiver is available at a time and the receiver has limited bandwidth.
In a wide-band sampling radio, a large portion of the spectrum is sampled (turned into digital
information) all at once. This sampling provides the basis for the use of several analysis tools and
receivers in the spectrum simultaneously, all from the one hardware sampler.
10.2 KEY SYSTEM COMPONENTS
10.2.1 Spectral Capture Unit (SCU)
Because the notion of a receiver is firmly established in both the amateur community and possibly
the rest of the world, it seemed inappropriate to describe the functionality of a wide-band sampling
system simply as a “receiver”. Instead, in the FLEX-6000 world there are one or more “Spectral
Capture Units”, or SCUs, that are responsible for the collection of wide-band data from the RF
spectrum. The SCU components are an antenna input, an optional set of receive pre-selectors, and
an analog-to-digital converter (ADC). Each SCU in the radio system can be connected to only a
single antenna at a time, but due to the sampling architecture, it may support any number of
receivers and spectrum displays. The SCU enables listening to multiple bands at the same time on
the same antenna. A hardware platform with multiple SCUs such as the FLEX-6700 allows for
monitoring multiple bands on different antennas or the ability to perform more complex noise
mitigation techniques that are available in multi-antenna systems.
10.2.2 Slice Receiver
Maestro can create two receivers out of the data collected from the SCU. How does this work?
The characteristics of the SCU sampled data stream vary by radio model but are typically 1-4Gbps
of data that contains all activity across a large section of the RF spectrum. In the FLEX-6700, for
example, an SCU tuned to the HF band collects every signal present in the spectrum from 0-73MHZ!
This data is not directly observable or understandable by an operator, so several tools exist for
understanding and using the SCU data, the first of which is the Slice Receiver. Each Slice Receiver is
tuned to a specific frequency just as a Variable Frequency Oscillator (VFO) would be in a traditional
radio. The Slice Receiver then takes this more manageable amount of data (typically describing 10-
20kHz of the band) and performs operations to output the signals required by the operator.
For example, in the case of a single sideband receiver, the Slice Receiver will demodulate the upper
(or lower) sideband of the data collected, will filter it according to the receiver filter settings, may
perform noise mitigation techniques on the data, and then ultimately passes it to an audio system
to become sound for the operator. Because the source of the Slice Receiver data is always the SCU
data and each Slice Receiver uses the same techniques to demodulate, filter, and convert the signal
into audio, each Slice Receiver shares the same base performance. For the operator, this means

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the FlexRadio Signature FLEX-6000 Series and is the answer not in the manual?

FlexRadio Signature FLEX-6000 Series Specifications

General IconGeneral
BrandFlexRadio
ModelSignature FLEX-6000 Series
CategoryTransceiver
LanguageEnglish

Related product manuals