Komatsu PC16R-3 User Manual

PREPARATION FOR EQUIPMENT INSTALLATION (only for machines with proportional controls)
273
6.5.8 PROGRAMMING THE CONTROL UNIT
WARNING
q Programming the control unit should be carried out by the Komatsu dealer.
(1) Leds
(2) Programming button
(3) Dip-switches
IMPORTANT
q First carry out the programming of the roller and then the
programming of the oil flow.
PROGRAMMING THE ROLLER
1 - Power up the control unit.
2 - Set the Dip-switch No. 4 to ON.
3 - Press the button (2) for 3 seconds.
4 - When the red led comes on you enter the programming and the green led switches off and blinks every 2 sec-
onds.
5 - With the roller in the central position, press the button (2) for 5 seconds. The green led blinks twice for 2 sec-
onds.
6 - Move the roller all the way to the right and press the button (2) for 5 seconds. The green led blinks three times
for 2 seconds.
7 - Move the roller all the way to the left and press the button (2) for 5 seconds. The green led does not blink and
the red led blinks rapidly.
8 - Press the button (2) for 2 seconds. The green led comes on confirming that the programming of the roller is
finished.
PROGRAMMING THE OIL FLOW
1 - Power up the control unit.
2 - Set the Dip-switch No. 4 to OFF.
3 - Press the button (2) for 3 seconds.
4 - When the red led comes on you enter the programming and the green led switches off and blinks every 2 sec-
onds.
5 - Very slowly move the roller until the equipment starts to move, then press the button (2) for 5 seconds to con-
firm. The green led blinks twice for 2 seconds.
6 - Move the roller again until the equipment moves at the maximum desired speed and press the button (2) for 5
seconds to confirm. The green led does not blink and the red led blinks rapidly.
7 - Press the button (2) for 2 seconds. The green led comes on confirming that the programming of the roller is
finished.
RKA63050
WEAM012405

Komatsu PC16R-3 Specifications

General

Brand	Komatsu
Model	PC16R-3
Category	Excavators
Language	English

Summary

Information on Safety

General Safety Information

Essential safety regulations, warnings, and precautions for operating and maintaining the machine.

Terminology for Hazard Levels

Safety and Accident Prevention

Safety, Noise, and Vibration Plates

Pictograms and Their Meanings

General Safety Precautions

Covers essential safety rules, behavior during anomalies, safety devices, and personal protective equipment.

Precautions Before Starting Engine

Outlines critical checks and safety measures to perform before starting the machine's engine.

Precautions When Working

Provides guidance on safe operating practices, including starting, moving, working on slopes, and hand signals.

Machine Operations and Controls

Instruments and Controls Overview

Details all instruments, gauges, switches, and controls necessary for operating the machine safely.

Before Starting the Engine

Lists essential visual checks and operational procedures required before starting the machine's engine.

Starting the Engine

Explains the procedures for starting the engine in both warm and cold climates, including critical safety steps.

Moving the Machine

Covers preliminary operations, forward/reverse movement, stopping, steering, and track gauge adjustments.

Transporting the Machine

Using the Machine in Cold Season

Long Periods of Inactivity

Troubleshooting Common Issues

Offers solutions for common problems related to electrical circuits, frame, engine, and other machine components.

Maintenance Procedures and Schedule

General Maintenance Guide and Notes

Covers general safety, waste disposal, special warnings, and basic maintenance guidelines for the machine.

Oil, Fuel, and Coolant Specifications

Parts Subject to Wear

Tightening Torques

Periodical Change of Safety-Related Components

Details safety-related parts that need periodic inspection and replacement to ensure machine safety and fire prevention.

Maintenance Plan

Outlines the recommended maintenance schedule based on operating hours and specific conditions.

Specific Maintenance Procedures

Technical Specifications and Capacities

Machine Technical Specifications

Lifting Capacities

Optional Equipment Installation and Use

General Safety Precautions for Attachments

Attachment Combinations and Configuration

Hydraulic Circuit for Attachments

Using the Equipment (Hammer)

Hydraulic Quick Coupler (Single-Effect)

Operating the Equipment (General)

Precautions for Optional Equipment