Stick mode table:
Mode left stick right stick right
ÙÚÙÚ
slider
1 Rudder Elevator Aileron Throttle
2 Rudder Throttle Aileron Elevator
3 Aileron Elevator Rudder Throttle
4 Aileron Throttle Rudder Elevator
Spoiler
5 Rudder Elevator Aileron Spoiler
6 Rudder Spoiler Aileron Elevator
7 Aileron Elevator Rudder Spoiler
8 Aileron Spoiler Rudder Elevator
Throttle
This is the procedure:
Action Effect
1. 4
r
Left to MENU
Confirm SETUP appears
2. r
Confirm MODEL appears
3. r
Confirm MODE appears
4. r
Open mode for set-
ting
Use the 3-D digi-adjustor to select your preferred
mode, and confirm your choice with a brief press r.
Note: idle trim
The trim button adjacent to the THROTTLE / SPOILER
stick is always used for throttle idle trim, even if the
right-hand slider is used to control throttle, as in modes
5 to 8.
13.3.3. Transmitter controls for the EASY type
The picture below shows the functions of the individual
transmitter controls for the EASY model type.
Switch functions
Teacher button Emergency throttle OFF
(Throttle Cut)
Combi-Switch not used
Dual Rate Servo 7
(Servo 4)
(Î 13.7.3)
Slider functions
Flap (camber-changing flap) Spoiler (modes 1 to 4)
or Throttle (modes 5 to 8)
13.3.4. Selecting idle forward / back
Menu: (SETUP, MODEL) TH R
The idle position of the transmitter control for throttle
(stick or slider) can be set to forward (towards the ae-
rial) or back (towards the pilot). When you set up a new
model, the setting is always
TH R = 0,
i.e. the idle position is “back”.
Note: throttle servo / speed controller works in the
wrong “sense”
If you have decided on the idle position, but the power
system in your model runs to full-throttle at this setting,
you must reverse the throttle servo (Î ). The idle
position must be left as it is, to ensure that THR-CUT (=
throttle cut = emergency motor OFF), throttle check (Î
13.3.5.) and the throttle / elevator mixer work correctly.
This is the procedure:
Action Effect
1. 4
r
Left to MENU
Confirm SETUP appears
2. r
Confirm MODEL appears
3. 3
Right to TH R THROTTLE reverse
4. r
Open TH R
for setting
“0” or “1” flashes in the bottom line.
THROTTLE R = “0” means:
the throttle idle position is back
THROTTLE R = “1” means:
the throttle idle position is forward
You can change the setting for THROTTLE R using the
3-D digi-adjustor. Press the 3-D digi-adjustor again to
end the process; the selected setting is then stored.
13.3.5. Setting Throttle Check
Menu: (
SETUP, MODEL) TH CHK
What is Throttle Check?
Throttle Check is a safety query of the throttle control.
This function avoids the danger of power systems
bursting into life unexpectedly, endangering and even
injuring you and others. It is a simple means of improv-
ing safety when operating any powered model.
How does Throttle Check work?
If the Throttle Check function is activated, the transmit-
ter checks whether the throttle control is at the idle
setting every time the transmitter is switched on, and
also when you switch to a different model memory. If
not, the screen continues to display the message
“GAS>0” until you move the throttle control to the idle
position. At the same time the throttle channel (receiver
output 4) is held at idle.
To Next Page
Loading...
Need help?
General
