11
The unit comprises a set of microswitches used to operate various
functions so as to render the system more suitable to user needs
and safer in the different ways of usage. All functions are activated
byplacingthedip-switchinthe“ON”positionwhiletheywillnotbe
activatedifthecorrespondingdip-switchesare“OFF”;somefunc-
tions do not have an immediate effect and only have sense in certain
conditions like.
!
ATTENTION: some of the programmable functions are
linked to safety aspects, very carefully evaluate the effects of
a function and see which function gives the greatest possible
level of safety.
When servicing a system, before you modify a programmable func-
tion, ascertain the reason why, during installation, certain choices
were made and then verify if, with the new programming, safety will
be impaired.
5) Programming
4.1) Operating modes
In the manual operating mode, the OPEN input enables an opening
movement, while the CLOSE input enables a closing movement. The
STEP-BY-STEP input enables an alternating opening and closing
movement. Movement stops as soon as the input command stops.
During an opening or closing manoeuvre, movement will stop also
when the command input or the signal from the safety devices is
disabled. During both opening and closing manoeuvres, the activa-
tion of the STOP command will cause the movement to stop imme-
diately. When a movement is stopped, stop the input command
before giving a command to start a new movement.
Whenoneoftheautomaticmodes(“Semiautomatic”,“Automatic”or
“Automatic+CloseAlways”) is operational, acommandimpulseto
the OPEN input causes an opening manoeuvre. A command impulse
totheSTEP-BY-STEPinputbeginsanalternatingclosingandopening
manoeuvre.AsecondimpulsetotheSTEP-BY-STEPinputortothe
same input the started the movement will cause it to stop.
Both in the opening and closing phases, the activation of the STOP
command will cause an immediate stopping of movement and a
short reverse run. If a continuous signal rather than an impulse is
maintained in a command input, a “prevalence” condition will be
generated causing the other command inputs to be disabled (this
is useful if you need to connect a clock or a Night/Day selec-
tor switch).
If an automatic operating mode has been chosen, the opening
manoeuvre will be followed by a pause and then a closing manoeu-
vre. If PHOTO triggers during the pause, the timer will be reset with
a new pause time; if, on the other hand, STOP is activated during
the pause, the closing function will be cancelled and the system will
switch to the STOP mode.
PHOTO will have no effect if it is triggered during the opening
manoeuvre, however if PHOTO is triggered during the closing
manoeuvre, the movement will reverse, pause, and then start to
close again.
5.1) Programmable functions
With the FUNCTIONS dip-switch you can select the various functioning modes and add the functions required according to this table:
Switch 1-2 Off Off =“Manual”movement,i.e.handoperated
On-Off =“Semiautomatic”movement
Off-On =“Automatic”movement,i.e.automaticclosing
On-On =“Automatic+alwaysclose”movement
Switch 3 On = Condominium operation < not available in manual mode >
Switch 4 On =Pre-ashing
Switch 5 On =Close5”afterPhoto<inautomaticmode>orCloseafterPhoto<insemiautomaticmode>
Switch 6 On =“Photo1”safetyalsoduringopeningmanoeuvres
Switch 7 On = Ramming
Switch 8 On = Deceleration
Switch 9 On = Maintain pressure
Switch 10 On = Phototest
Switch 11 On = Courtesy Light in impulse mode
Switch 12 On = Close becomes Open for Pedestrians
Note 1: Somefunctionsareonlyavailableincertainconditions;theseareexplainedbythenotesbetweenthecharacters“<...>”.
EN
To Next Page
Loading...
Need help?
General
