ABB FSO-21 User Manual

Configuration 353
 How to configure SSE with immediate STO, SBC after or before STO
The configuration is identical to the SBC after or before STO functions with these
differences:
• parameter STO.13 Restart delay after STO is not used
• SSE input parameters (SSE.11 SSE input A and SSE.12 SSE input B) are used
instead of STO input parameters
• SSE output parameters (SSE.21 SSE output and SSE.22 SSE completed output)
are used instead of STO output parameters.
See sections How to configure SBC after STO on page 333 and How to configure
SBC before STO on page 335.
For more information on the SSE with immediate STO and SBC after STO function,
see page 109.
For more information on the SSE with immediate STO and SBC before STO function,
see page 112.
 How to configure SSE with immediate STO with speed limit
activated SBC
This safety function requires that an encoder is used. Configure the safety encoder
interface first (see section Configuring the safety encoder interface on page 313).
The configuration is identical to the STO with speed limit activated SBC function with
these differences:
• parameter STO.13 Restart delay after STO is not used
• SSE input parameters (SSE.11 SSE input A and SSE.12 SSE input B) are used
instead of STO input parameters
• SSE output parameters (SSE.21 SSE output and SSE.22 SSE completed output)
are used instead of STO output parameters.
Note: If you configure the SSE with immediate STO with speed limit activated SBC
function, this activates the same function in the STO function (see section How to
configure STO with speed limit activated SBC on page 337).
For more information on the SSE with immediate STO with speed limit activated SBC
function, see page 115.

ABB FSO-21 Specifications

General

Brand	ABB
Model	FSO-21
Category	Control Unit
Language	English

Summary

Safety instructions

Electrical safety precautions

Electrical safety precautions for personnel working on drives, motor cables, or motors.

Introduction to the manual

Supported safety functions

Details safety functions supported by FSO-21 module per EN/IEC 61800-5-2.

Overview

Intended use of the FSO module

FSO-21 adds safety functionality to drives, supporting PROFIsafe and safety encoders.

Overview of safety functions

Safe torque off (STO)

Activates drive STO function to bring machine to a no-torque state by stopping motor.

Safe stop 1 (SS1)

Safely stops motor by ramping down speed to zero, monitored by time or ramp method.

Safe stop emergency (SSE)

Stops motor safely by coasting or ramping down, similar to STO or SS1.

Safe brake control (SBC)

Provides safe output for external safety brakes, always combined with drive STO.

Safely-limited speed (SLS)

Prevents motor exceeding user-defined speed limits; activates SSE if trip limit is reached.

Variable Safely-limited speed (SLS)

Allows scaling of SLS limits via safety PLC using PROFIsafe.

Safe maximum speed (SMS)

Protects machine from high speeds/frequencies; can be permanently on or off.

Prevention of unexpected start-up (POUS)

Prevents machine from starting unexpectedly by activating drive STO.

Safe speed monitor (SSM)

Provides safe output signal for motor speed within user-defined limits.

Safe direction (SDI)

Monitors correct motor rotation; activates SSE if forbidden direction is exceeded.

Safe acceleration range (SAR)

Provides safe deceleration ramp monitoring for other safety functions.

Safety functions

Cascade

Planning for installation

Installation

Mechanical installation

Electrical installation

Connection procedure

Configuration

Configuring the FSO module

Overview of safety system configuration process: risk assessment, requirements, design, validation.

FSO configuring procedure

Steps for setting FSO parameters using Drive composer pro PC tool.

Configuring general settings

Configuring the safety encoder interface

Configuring the safety fieldbus communication

Configuring I/O

Configuring SBC

Configuring SBC function with STO, SSE, SS1, considering delays and speed limits.

How to configure the SBC in the STO function

Setting SBC usage, delay, and speed limit parameters for SBC in STO function.

Configuring STO

Setting FSO parameters for STO function: input, acknowledgement, output configurations.

How to configure SS1 with time monitoring (SS1-t)

Setting SS1 parameters for time monitoring: activation, delays, acknowledgement, outputs.

How to configure SS1 with ramp monitoring (SS1-r)

Setting SS1 parameters for ramp monitoring: activation, SAR1, acknowledgement, outputs.

How to configure SSE with immediate STO

Configuring SSE with immediate STO: activation, acknowledgement, and output settings.

How to configure SSE with ramp monitoring

Configuring SSE with ramp monitoring: activation, SAR0, acknowledgement, outputs.

Configuring SLS

Setting FSO parameters for SLS functions (SLS1-4, Variable SLS): limits and trip limits.

How to configure SLSn with time monitoring

Configuring SLSn with time monitoring: activation, delay, acknowledgement, outputs.

How to configure Variable SLS with time monitoring

Configuring Variable SLS with time monitoring: activation, acknowledgement, delays, outputs.

Configuring SMS

Configuring SMS function (version 1 or 2) for protection against high speeds/frequencies.

Configuring POUS

Configuring POUS function to prevent unexpected start-up: activation, acknowledgement, inputs, delay, outputs.

Configuring SSM

Configuring SSM function for monitoring motor speed between user-defined limits.

Configuring SDI

Configuring SDI function to monitor correct motor rotation, requiring an encoder.

Configuring mute times

How to configure limit hit situations

Parameters

FSO-21 parameters

Start-up

Safety considerations

Verification and validation

Validation procedure

Validation of the PROFIsafe connection

Validation of the safety encoder interface

Validation of the SBC function

Validates SBC function, ensuring correct wiring and configuration for delayed brake and speed limit activated brake.

Validation of the SSE function

Validates SSE function: immediate STO, emergency ramp with safe speed estimate or encoder.

Validation of the SS1 function

Validates SS1 function: inputs, SAR1/time monitoring settings, acknowledgement, indications.

Validation of the SLS functions

Validates SLS functions (SLS1-4): inputs, functionality, acknowledgement, indications for ramp/time monitoring.

Validation of the variable SLS function

Validates variable SLS function: PLC scaling, inputs, acknowledgement, outputs.

Validation of the SMS functions

Validates SMS functions (version 1 and 2): activation, limits, SSE function configuration.

Validation of the POUS function

Validates POUS function: inputs, outputs, activation, acknowledgement, functionality.

Validation of the SSM functions

Validates SSM functions (SSM1-4): inputs, outputs, activation, limits.

Validation of the SDI function

Validates SDI functions: inputs, configuration, tolerance limits, acknowledgement for ramp/time monitoring.

Validation of the cascaded safety function

Fault tracing

Faults, warnings and events

FSO recovery

Maintenance

Component replacement in the safety circuit

Instructions for replacing FSO/FSE modules, control units, or FB modules, ensuring safety during process.

Replacing the FSO module

Replacing the FB module in PROFIsafe network

Start-up and validation test

Factory reset

Resets FSO to factory settings; requires reconfiguration. Backup safety file before reset.

Technical data

Electrical data

Safety functions

Categorizes safety functions into Stopping and Speed-related, listing specific functions.

Stopping functions

Speed-related functions

POUS

Prevention of unexpected start-up function.

Safety data

Determines SIL/PL capability by adding failure rates of components.

PROFIsafe

Subsystem for PROFIsafe connection reliability, handled by FSO module via FENA/FPNO.

FSO safety calculations guide (without PROFIsafe)

FSO safety calculations guide (with PROFIsafe)

Basic safety data

Lists FSO-21 safety data related to IEC 61508, EN ISO 13849-1, IEC 61511, EN IEC 62061.