RP/0/RSP0/CPU0:router(config-bgp)# address-family vpnv4 unicast
RP/0/RSP0/CPU0:router(config-bgp-af)#
L2VPN Address Family Configuration Mode
The following example shows how to enter L2VPN address family configuration mode:
RP/0/RSP0/CPU0:router(config)# router bgp 100
RP/0/RSP0/CPU0:router(config-bgp)# address-family l2vpn vpls-vpws
RP/0/RSP0/CPU0:router(config-bgp-af)#
Neighbor Submode
Cisco IOS XR BGP uses a neighbor submode to make it possible to enter configurations without having to
prefix every configuration with the neighbor keyword and the neighbor address:
•
Cisco IOS XR software has a submode available for neighbors in which it is not necessary for every
command to have a “neighbor x.x.x.x” prefix:
In Cisco IOS XR software, the configuration is as follows:
RP/0/RSP0/CPU0:router(config-bgp)# neighbor 192.23.1.2
RP/0/RSP0/CPU0:router(config-bgp-nbr)# remote-as 2002
RP/0/RSP0/CPU0:router(config-bgp-nbr)# address-family ipv4 unicast
•
An address family configuration submode inside the neighbor configuration submode is available for
entering address family-specific neighbor configurations. In Cisco IOS XR software, the configuration
is as follows:
RP/0/RSP0/CPU0:router(config-bgp)# neighbor 2002::2
RP/0/RSP0/CPU0:router(config-bgp-nbr)# remote-as 2023
RP/0/RSP0/CPU0:router(config-bgp-nbr)# address-family ipv6 unicast
RP/0/RSP0/CPU0:router(config-bgp-nbr-af)# next-hop-self
RP/0/RSP0/CPU0:router(config-bgp-nbr-af)# route-policy one in
•
You must enter neighbor-specific IPv4, IPv6, VPNv4, or VPNv6 commands in neighbor address-family
configuration submode. In Cisco IOS XR software, the configuration is as follows:
RP/0/RSP0/CPU0:router(config)# router bgp 109
RP/0/RSP0/CPU0:router(config-bgp)# neighbor 192.168.40.24
RP/0/RSP0/CPU0:router(config-bgp-nbr)# remote-as 1
RP/0/RSP0/CPU0:router(config-bgp-nbr)# address-family ipv4 unicast
RP/0/RSP0/CPU0:router(config-bgp-nbr-af)# maximum-prefix 1000
•
You must enter neighbor-specific IPv4 and IPv6 commands in VRF neighbor address-family configuration
submode. In Cisco IOS XR software, the configuration is as follows:
RP/0/RSP0/CPU0:router(config)# router bgp 110
RP/0/RSP0/CPU0:router(config-bgp)# vrf vrf_A
RP/0/RSP0/CPU0:router(config-bgp-vrf)# neighbor 11.0.1.2
RP/0/RSP0/CPU0:router(config-bgp-vrf-nbr)# address-family ipv4 unicast
RP/0/RSP0/CPU0:router(config-bgp-vrf-nbr-af)# route-policy pass all in
Cisco ASR 9000 Series Aggregation Services Router Routing Configuration Guide, Release 5.1.x
20 OL-30423-03
Implementing BGP
BGP Configuration
To Next Page
Loading...
Need help?
General
