RL78/G13 CHAPTER 1 OUTLINE
R01UH0146EJ0100 Rev.1.00 21
Sep 22, 2011
• 100-pin plastic LQFP (14 × 20)
P140/PCLBUZ0/INTP6
P141/PCLBUZ1/INTP7
P142/SCK30/SCL30
P143/SI30/RxD3/SDA30
P144/SO30/TxD3
P145/TI07/TO07
P00/TI00
P01/TO00
P02/ANI17/SO10/TxD1
P03/ANI16/SI10/RxD1/SDA10
P04/SCK10/SCL10
P102/TI06/TO06
P130
P20/ANI0/AV
REFP
P21/ANI1/AV
REFM
P22/ANI2
P23/ANI3
P24/ANI4
P25/ANI5
P26/ANI6
P27/ANI7
P150/ANI8
P151/ANI9
P152/ANI10
P153/ANI11
P154/ANI12
P155/ANI13
P156/ANI14
P100/ANI20
P147/ANI18
P60/SCLA0
P61/SDAA0
P62/SCLA1
P63/SDAA1
P31/TI03/TO03/INTP4/(PCLBUZ0)
P64/TI10/TO10
P65/TI11/TO11
P66/TI12/TO12
P67/TI13/TO13
P77/KR7/INTP11/(TXD2)
P76/KR6/INTP10/(RXD2)
P75/KR5/INTP9
P74/KR4/INTP8
P73/KR3
P72/KR2/SO21
P71/KR1/SI21/SDA21
P70/KR0/SCK21/SCL21
P06
P05
EV
SS1
P80/(SCK10)/(SCL10)
P81/(SI10)/(RXD1)/(SDA10)
P82/(SO10)/(TXD1)
P83
P84/(INTP6)
P85/(INTP7)
P86/(INTP8)
P87/(INTP9)
P30/INTP3/RTC1HZ/SCK11/SCL11
EV
DD1
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
P146/(INTP4)
P111/(INTP11)
P110/(INTP10)
P101
P10/SCK00/SCL00/(TI07)/(TO07)
P11/SI00/RxD0/TOOLRxD/SDA00/(TI06)/(TO06)
P12/SO00/TxD0/TOOLTxD/(INTP5)/(TI05)/(TO05)
P13/TxD2/SO20/(SDAA0)/(TI04)/(TO04)
P14/RxD2/SI20/SDA20/(SCLA0)/(TI03)/(TO03)
P15/SCK20/SCL20/(TI02)/(TO02)
P16/TI01/TO01/INTP5/(SI00)/(RXD0)
P17/TI02/TO02/(SO00)/(TXD0)
P57/(INTP3)
P56/(INTP1)
P55/(PCLBUZ1)/(SCK00)
P54/SCK31/SCL31
P53/SI31/SDA31
P52/SO31
P51/SO11
P50/SI11/SDA11
P120/ANI19
P47/INTP2
P46/INTP1/TI05/TO05
P45/SO01
P44/SI01/SDA01
P43/SCK01/SCL01
P42/TI04/TO04
P41
P40/TOOL0
RESET
P124/XT2/EXCLKS
P123/XT1
P137/INTP0
P122/X2/EXCLK
P121/X1
REGC
V
SS
EV
SS0
V
DD
EV
DD0
Cautions 1. Make EVSS0, EVSS1 pins the same potential as VSS pin.
2. Make V
DD pin the potential that is higher than EVDD0, EVDD1 pins (EVDD0 = EVDD1).
3. Connect the REGC pin to Vss via a capacitor (0.47 to 1
μ
F).
Remarks 1. For pin identification, see 1.4 Pin Identification.
2. When using the microcontroller for an application where the noise generated inside the microcontroller
must be reduced, it is recommended to supply separate powers to the V
DD, EVDD0 and EVDD1 pins and
connect the VSS, EVSS0 and EVSS1 pins to separate ground lines.
3. Functions in parentheses in the above figure can be assigned via settings in the peripheral I/O redirection
register (PIOR).
<R>
To Next Page
Loading...
Need help?
General
