6 – ENGLISH
3.2 PRODUCT USAGE LIMITS
The data relative to the performances of products of the SPIDER range
are shown in the “TECHNICAL SPECIFICATIONS” chapter (page 59)
and is the only data that allows for properly assessing whether the product
is suitable for its intended use.
The structural characteristics of SPIDER products make them suitable for
use on sectional and overhead doors within the limits shown in Tables “
Table 1” , “Table 2” and “Table 3”
Table 1
OPERATING LIMITS OF SPIDER GEARMOTORS
Model
Type of
guide
Sectional
doors
Non-
protruding
overhead
doors (with
accessory
SPA5)
Protruding
overhead
doors (with
accessory
SPA5) or
with springs
(without
SPA5)
SPIDER800
SR32/16
4.4 x 2.6
metres
(W x H)
4.2 x 2.4
metres
(W x H)
4.2 x 3
metres
(W x H)
SR32/16
+ SR08 or
SR40
3.4 x 3.4
metres
(W x H)
3.1 x 3.4
metres
(W x H)
3.6 x 3.6
metres
(W x H)
SPIDER1200BLW
SR32/16
6.5 x 2.6
metres
(W x H)
6.5 x 2.4
metres
(W x H)
6.5 x 3
metres
(W x H)
SR32/16
+ SR08 or
SR40
5 x 3.4
metres
(W x H)
4.9 x 3.4
metres
(W x H)
5.6 x 3.6
metres
(W x H)
Table 2
LIMITS IN RELATION TO LEAF HEIGHT
Door height
Maximum no. of
cycles/hour
Maximum no. of
consecutive cycles
Up to 2 metres 20 10
2–2.5 metres 15 7
2.5–3 metres 12 5
3–3.5 metres 10 4
Table 3
LIMITS IN RELATION TO THE FORCE REQUIRED TO MOVE THE LEAF
Force to move the door SPIDER800 SPIDER1200BLW
Up to 250 N 25% 15%
250 - 400 N 42% 28%
400 - 500 N 55% 35%
500 - 650 N 70% 45%
650 - 800 N 85% 55%
800 - 100 N - 70%
1000 - 1200 N - 85%
The height of the door allows for determining both the maximum number
of cycles per hour and the number of consecutive cycles.
The force required to move the door allows for determining the cycle re
-
duction percentage. With a leaf 2.2 metres high, a maximum of 15 cy-
cles/hour and up to 7 consecutive cycles can be completed. If 550 N
are required to move the leaf and SPIDER800 is used, the cycle must be
reduced by 70%.
In this case, the maximum cycles/hour amount to 10 and the consecutive
cycles are equal to 5.
a
The control unit is equipped with a manoeuvre limiting
device that prevents possible overheating; it is based on
the motor load and duration of the cycles, and intervenes
when the maximum limit is exceeded.
a
1 kg = 9.81 N. consequently, for example, 500 N = 51 kg
The measurements shown in “Table 1” are purely indicative and are only
needed for making a rough estimate. The actual suitability of SPIDER for
automating a specic door depends on the degree of leaf balancing, guide
friction and other aspects, including occasional events such as wind pres
-
sure or the presence of frost, which could obstruct the leaf’s movement.
To determine the actual conditions, the force required to move the leaf
throughout its path must be measured, to ensure that this value does not
exceed the “rated torque” specied in the “TECHNICAL SPECIFICA
-
TIONS” chapter (page 59).
a
The control unit is equipped with a manoeuvre limiting
device that prevents possible overheating; it is based on
the motor load and duration of the cycles, and intervenes
when the maximum limit is exceeded.
3.3 PRODUCT IDENTIFICATION AND OVERALL
DIMENSIONS
The overall dimensions of the product are shown in “Figure 3”.
105,5 mm
138,5 mm
225 mm
294 mm
3
3.4 RECEIPT OF THE PRODUCT
All the components contained in the kit are illustrated and listed below.
G
H
A
C
4
A Gearmotor
B Unlocking system and metal hardware (screws, washers, etc.)
C Drawbar
D Door mounting bracket
E Joining element for guide (in case of a 2-piece guide)
F Assembled / pre-assembled guide
G Wall mounting bracket
H Ceiling mounting bracket
I Motor mounting bracket
To Next Page
Loading...
Need help?
General
