Sony MVS-6530 User Manual

USO RESTRITO
Macro Operations in the Flexi Pad 285
Chapter
15
Macros
To switch auto insert mode on or off, press the [AUTO
INS] button.
Creating a new macro
1 Recall an empty register ( 1 p. 283).
2 Press the [MCRO] button and then press the [EDIT
ENBL] button.
This switches the memory recall section to macro
editing mode.
3 If required, press the [AUTO INS] button to toggle the
auto insert mode on or off.
4 Create the events (carry out the control panel
operations to be registered as events in the macro).
You can include pause events ( 1 p. 287).
For details about events that can be registered,
1 “Events” (p. 281).
When auto insert mode ( 1 p. 284) is on, execution of
a control panel operation automatically registers an
event in the macro.
When auto insert mode is off, proceed to step 5.
Notes
• During macro editing, if you press any of the mode
selection buttons in the Flexi Pad other than the
[MCRO] button ([WIPE] button, [DME WIPE]
button, and so on), the executed operation is also
registered as an event. In this case, the [MCRO]
button stays lit red.
• Even during macro editing, you can carry out
keyframe operations using the following buttons:
[EFF LOOP], [STOP NEXT], [NORM], [REV],
[NORM/REV], [REWIND], [RUN]
• During macro editing, if you press a button for
which a macro attachment is set, the outcome is as
described in “To merge a macro for which a macro
attachment is set” ( 1 p. 285).
5 When auto insert mode is off, press the [INS] button to
register the event.
6 Repeat steps 4 and 5 to register the required events in
the macro.
This registers the events in the macro, in the order the
operations were carried out on the control panel.
7 Press the [STOR] button.
8 Enter the register number to save with the numeric
keypad buttons.
There is no need to enter a number if saving into the
register recalled in step 1.
9 Press the [ENTR] button.
This saves the created macro in the register, and
editing ends. The [MCRO] button lights amber.
To merge a macro for which a macro attachment
is set
While creating/editing a macro, if you press a button for
which a macro attachment is set, the macro in the register
assigned to the button is recalled, and the following occurs.
• When auto insert mode is on, it is merged with the macro
being edited. However, the macro assigned to the button
is not executed.
• When auto insert mode is off, it is stored in the paste
buffer. Pressing the [PSTE] button merges it with the
macro being edited.
Specifying an edit point
1 Recall the register for the macro (1 to 250) you want to
edit ( 1 p. 283).
2 Press the [EDIT ENBL] button, turning it on.
This switches the memory recall section to macro
editing mode.
3 Using any of the following methods, specify the edit
point.
• To move the edit point to the event immediately
following the current macro event, press the [>>
NEXT] button.
• To move the edit point to the event immediately
preceding the current macro event, press the [<< PREV] button.
• To move to an edit point by specifying an event
number (the number showing the position of the
event in the macro execution sequence), press the
[GOTO EVNT] button, then enter the event number
and confirm with the [ENTR] button.
Inserting an event
1 Specify the edit point ( 1 p. 285).
2 If required, press the [AUTO INS] button to toggle the
auto insert mode on or off.
3 Create the event.
When auto insert mode ( 1 p. 284) is on, the event is
automatically added to the macro.
When auto insert mode is off, proceed to step 4.

Sony MVS-6530 Specifications

General

BNC input ports	48
BNC output ports	32
RJ-45 input ports	4
Product color	Black
AC input voltage	100 - 240 V
AC adapter frequency	50/60 Hz
AC adapter input current	4 A
Storage temperature (T-T)	-20 - 55 °C
Operating temperature (T-T)	5 - 40 °C

Weight and Dimensions

Depth	486 mm
Width	482 mm
Height	176 mm
Weight	21000 g