Sony MVS-6530 User Manual

USO RESTRITO
208
Applying Special Effects (Lighting and Recursive Effects)
No.
Parameter
Adjustment
1
Decay
Degree to which the trail is left
2
Shift H
Extension in the horizontal
direction
3
Shift V
Extension in the vertical direction
No.
Parameter
Adjustment
1
Luminance
Luminance
2
Saturation
Saturation
3
Hue
Hue
No.
Parameter
Adjustment
1
Luminance
Luminance
2
Saturation
Saturation
Chapter
10
DME
Operations
• When Wind is turned on, any of the following effects
that are on are turned off: Trail, Motion Decay,
Keyframe Strobe.
Applying the wind effect
1 Open the DME >Light/Trail >Wind menu (4155).
2 Press [Wind], turning it on.
3 Set the following parameters.
4 To erase the afterimages, press [Wind Eraser], turning
it on.
Selecting the signal for the afterimage
portion
In the <Wind Source> group of the Wind menu (4155),
select the image to fill the afterimage portion.
Notes
• [Mix Color] or [Ext Video] can only be applied to one of
the background ( 1 p. 215), flex shadow ( 1 p. 178),
trail ( 1 p. 204), and wind effects. If you select [Mix
Color] or [Ext Video] in one of these effects, a selection
of [Mix Color] or [Ext Video] in any of the other effects
is disabled, and [Flat Color] is selected in its place.
• When executing combining four channels of DME
images, [Mix Color] and [Ext Video] in the flex shadow
and background effects cannot be selected.
Freeze Video: Use freeze images of the input video as
source of the trail.
Flat Color: Use a flat color matte as source of the trail.
You can set the following parameters.
Hue Rotate: Use a single color matte with the hue
changing for each frame as the afterimage. You can set
the following parameters.
No.
Parameter
Adjustment
3
Hue Speed
Rate at which hue changes
Mix Color: Insert a mix color signal ( 1 p. 183) in the
afterimage portion.
Ext Video: Insert the external video signal input to the Ext
IN connector in the afterimage portion.
Rainbow: Use a freeze image with the hue changing every
frame in the afterimage portion. The difference from
“Hue Rotate” is that many colors appear
simultaneously.
For details about the Rainbow parameters, see the
“Hue Rotate” item above.
Applying modulation to the afterimage
portion
1 In the Wind menu (4155), press [Modulation], turning
it on.
2 Set the following parameters.
No.
Parameter
Adjustment
1
Amp H
Horizontal amplitude of the wave
2
Freq H
Frequency of waves in horizontal
direction
3
Amp V
Vertical amplitude of the wave
4
Freq V
Vertical frequency of the wave
For details about Priority, Wind Freeze Timing, Wind
Eraser, Defocus, Dust, and Combine Process in the
Wind menu, 1 “Trail Settings” (p. 204).
Spotlighting Settings
You can set up to three spotlight sources (lights 1 to 3).
Notes
• The spotlighting function is not supported by the MKS-
6570 or MVE-8000A.
• The BZDM-9050 Texture Lighting Software (for MVE-
9000) is required to set lights 2 and 3.
• When the global effect Combiner is enabled, the settings
of the smallest-numbered channel selected for the
Combiner are used.
Adjustments to the image surface
The following adjustments can be made to the image
surface struck by the light.
• Adjusting the brightness of the whole image
• Selecting the image surface effect
• Test sphere function
• Adjusting the bumpiness of the image surface

Sony MVS-6530 Specifications

General

BNC input ports	48
BNC output ports	32
RJ-45 input ports	4
Product color	Black
AC input voltage	100 - 240 V
AC adapter frequency	50/60 Hz
AC adapter input current	4 A
Storage temperature (T-T)	-20 - 55 °C
Operating temperature (T-T)	5 - 40 °C

Weight and Dimensions

Depth	486 mm
Width	482 mm
Height	176 mm
Weight	21000 g