Sony MVS-6530 User Manual

USO RESTRITO
334
Setting Button Assignments
1
In the Engineering Setup >Panel >Router Remote
>RTR Mode Setting menu (7323.1), select the
destination selection button to set.
2
Press [SS Enable], turning it on or off.
On: When a snapshot applying to the router is
Chapter
18
Control
Panel
Setup
Selecting a Destination Selection
Button for a Snapshot
recalled, the recall also applies to the selected
destination selection button.
Off: When a snapshot applying to the router is
recalled, the recall does not apply to the selected
destination selection button.
Notes
When a destination selection button is set to [Inhibit],
then even if [SS Enable] is on, the snapshot for that
destination is not recalled.
Setting Button
Assignments
You can assign the [PREFS 1] to [PREFS 16] buttons in
the menu panel and the cross-point control block buttons.
This assigns recalling frequently used menus (menu
shortcuts), enabling/disabling functions (recalling utility
commands) and recalling shotbox registers or macro
registers.
Assigning Functions to User
Preference Buttons
You make settings for the user preference buttons in the
menu panel.
1 In the Engineering Setup >Panel >Prefs/Utility menu
(7324), select the button to be assigned.
2 In the <Action> group, select the function to be
assigned.
Menu Shortcut: Assigns a frequently used menu to be
recalled (menu shortcut).
Utility Command: Assigns a function enable/disable
or similar operation (utility command).
Macro Recall: Assigns a macro register recall.
Shotbox Recall: Assigns a shotbox register recall.
3 Depending on the selection in step 2, make the
following settings.
If [Menu Shortcut] is selected: With the user
preference buttons flashing, press one of the user
preference buttons after displaying the menu for
which you want to create a shortcut to assign the
menu shortcut. To finish the assignment, press
[Menu Shortcut] again.
If [Utility Command] is selected: Select the
command you want to assign on the right side of
the status area.
No.
Parameter
Adjustment
3
Command
Command selection
4
GPI No
GPI number
a)
a) SWR GPI Test Fire, Panel GPI Test Fire, and DCU GPI Test Fire
commands only.
If [Macro Recall] is selected: Select the macro
register you want to assign.
No.
Parameter
Adjustment
3
Macro
Macro register selection
If [Shotbox Recall] is selected: Select the shotbox
register you want to assign.
No.
Parameter
Adjustment
3
Shotbox
Shotbox register selection
4 If you selected a function other than [Menu Shortcut]
in step 2, press [Action Set].
To cancel an assignment
Select the button, then press [Clear].
To display register names in the “Utility
Command” column
If in step 2 you select [Macro Recall] or [Shotbox Recall],
press [Reg Name Display] to select whether or not register
names appear in the “Utility Command” column.
Using the [PREFS 9] to [PREFS 16]
settings
There are sixteen user preference buttons that can be set,
[PREFS 1] to [PREFS 16], but there are only eight user
preference buttons present in the menu panel. By default
these buttons are assigned to the [PREFS 1] to [PREFS 8]
settings.
Therefore, to use the settings of [PREFS 9] to [PREFS 16],
it is necessary to assign these settings to buttons in the
menu panel in the Engineering Setup >Panel >Config
>Menu Panel menu (7321.19).

Sony MVS-6530 Specifications

General

BNC input ports	48
BNC output ports	32
RJ-45 input ports	4
Product color	Black
AC input voltage	100 - 240 V
AC adapter frequency	50/60 Hz
AC adapter input current	4 A
Storage temperature (T-T)	-20 - 55 °C
Operating temperature (T-T)	5 - 40 °C

Weight and Dimensions

Depth	486 mm
Width	482 mm
Height	176 mm
Weight	21000 g