2. Safety
To prevent personal injury
• Isolate electrically before replacing the lamp o r lamp house. Caution: Hot lamp (house).
• Caution: High pres sure lam p may explode if improperly handled. Refer servicing to qualified se rvice personnel.
• To prevent injury and physical dam age, always read this man ual and all labels on the system before inserting the lam p casing,
powering the projector o r adjusting the projector.
• To pre vent injury, take note of the weight of the projector. Minimum 4 adult persons are needed to c arry the projector.
• To prevent injury, ensure that the lens and all cove r plates are correctly ins talled. See installation procedures.
• Warning: high intensity light beam. NEVER look into the lens ! High luminance c ould result in damage to the eye.
• Warning: extremely high brightness lamps: T his pr ojector uses extrem ely high brightness lamps. Never attem pt to look
directly into the lens or at the lamp. If the projection distance is less than 6 meter, any person needs to be at leas t 4 m eters
away from the projected image. Avoid clos e range reflection of the projected image on a ny reflecting s urface (such as glass,
metal, … ) . When operating the projector, we strongly recommend wearing suitable safety glasses.
• Before attempting to remove any of the projector ’s covers, disconnect the projector power cord for removal of all power from
the projector.
• When required to remove all power from the projector, to access parts inside, always disconnect the projector powe r cord for
removal of all pow er from the projector.
• Do not place this equipmen t on an unstable c art, stand, or table. The product m ay fall, causing serious damage to i
t and
possible injury to the user.
• It is hazardous to operate without lens or shield. Lenses, s hields or ultra violet screens shall be changed if they have become
visibly damaged to such an extent that their effectiveness is impaired. For exam ple by cracks or deep s cratches.
• Warning: Pro tection from ultraviolet radiation: D o not look directly in the light beam. The lamp c ontained in this product is
an intense source of light and heat. One component of the light emitted from this lam p is ultraviolet light. P otential eye and skin
hazards are present when the lamp is energized due to ultraviolet radiation. Avoid unneces sary exposure. Protect yourself and
your employees by making them aware of the hazards and how to protect thems elves. P rotecting the skin can be accom plished
by w earing tightly wov en garments and gloves. Protecting the eyes from UV can be ac complished by wearing safety glasses
that are designed to provide UV protection. In addition to the UV, the v isible light from the lamp is intense and should also be
considered when choosing pr otective eye wear.
• Mercury Vapor Warnings: Keep the following warnings in m ind w hen using the projector. The lamp used in the projector
contains m ercury. In case o f a lamp r upture, explosion there w ill be a m ercury vapor emission. In order to minimize the potential
risk of inhaling mer cury vapors:
- Ensure the projector is installed only in ventilated rooms.
- Replace the lamp module before the end of its operational life.
- Promptly v entilate the room after a lamp rupture, explosion has oc curred, evacuate the r oom (particularly in case of a preg-
nant wom an).
- Seek medical attention if unusual health conditions oc cur after a lamp rupture, explosion, such as headache, fatigue, s hort-
ness of breath, chest-tightening coughing or nausea.
• Exposure to UV radiation: Som e m edications are known to m ake individuals extra sensitive to UV radiation. T he A mer ican
Conference of G overnmen tal Industrial H ygienists (ACGIH)
recommends occupational UV exposure for an-8 hour day to be
less than 0,1 micro-watts per square centimeters of effective U V radiation. A n evaluation of the workplace is advised to assure
employees are not exposed to cumulative radiation levels exceeding these government guidelines.
To prevent fire hazard
• Do not place flam mable or combustible materials near the projector!
• Barco large screen pr ojection products are des igned and manufactured to meet the most stringent s afety regulations. This
projector radiates heat on its external surfaces an d from v entilation ducts during norm al operation, which is both normal and
safe. Exposing flammable or co mbus tible materials into close proximity of this projector could result in the spontaneous ignition
of that material, resulting in a fire. For this rea son, it is absolutely necessary to leave an “exclusion zone” around all e xternal
surfaces of the projector whereby no flammable o r combustible materials are present. The exclusion zon e mu st be not less
than 40 cm (16”) for all DLP Cinema projectors. The exclusion zone on the lens side mu st be at least 5 m. Do not cover the
projector or the lens with any material while the pr ojector is in operation. Keep flammab le a nd combustible m aterials away from
the projector at all times . Moun t the projector in a well ventilated ar ea away from sources of ignition and out of direct sun light.
Never expose the projector to rain or moisture. In the event of fire, use sand, CO
2
or dry powder fire extinguishers. Never use
water on an electrical fire. Always have ser vice performed on this projector by authorized B arco service personnel. Always
insist on gen uine Barco replacement parts. Never use non-Barco replacement parts as they may degrade the safety of this
projector.
• Slots and openings in this equipment are p rovided for ventilation. To ensure reliable operation of the projector an d to protect
it from ov erheating, these opening
s must not be blocked or covered. The openings should never be blocked by p lacing the
projector too close to walls, or other similar surface. This projector should never be placed near or over a radiator or heat
register. Th is p rojector should not be placed in a built-in installation or enclosure unless proper ventilation is provided.
• Projection rooms must be well ventilated or cooled in order to avoid build up of heat. It is necessary to v ent hot e xhaust air from
console to the outside of the building.
• Let the projector cool c ompletely before s toring. Rem ove cord from the projector when storing.
• Heat s ensitive m aterials should not be placed in the path of the ex haust air or on the lamp house.
8
R5906693 DP2K-E SERIES 19/06/2015
To Next Page
Loading...
Need help?
General
