2. Safety
To prevent projector damage
• This projector has been d esigned for use with a spe cific lamp (house) type. See installation instructions for its correct type.
•Theairfilters of the projector must be cleaned or replaced on a regular bas is (a "clean" booth would be m onthly-minimum).
Neglecting this could result in disrupting th e air flow inside the projector, causing overheating. Overheating may lead to the
projector shutting down during operation.
• The projector must alway s b e installed in a m anner which ensures free flow of air into its air inlets.
• In order to ens ure that correct airflow is maintained, and that the projector comp lies w ith E lectromagnetic Compatibility (EMC )
and sa fety requirements, it should always be operated with all of it’s covers in place.
• Slots and openings in the cabinet are provided for ventilation. To ensure reliable op eration of the product and to protect it from
overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the p roduct
on a bed, sofa, rug, or other similar surface. This product should never be placed near or over a radiator or heat register. The
device shou ld not be placed in a built-in installation or enclosure unless proper v entilation is provided.
• Ensure t hat nothing can be spilled on, or dropped inside the projector. If this does happen, switch off and remove all power
from the projector. Do not operate the projector again until it has been checked by qualified se rvice pe
rsonnel.
• Do not block the projector cooling fans o r free air movem ent around the pr ojector. Loose papers or other objects may n ot be
nearer to the projector than 10 cm (4") on any side.
• Do not use this equipm ent near water.
• Proper oper ation of the projector can only be guar anteed in table mounting. It is not permitted to use t he projector in another
position. S ee installation procedure for correct installation. A ceiling mou nt will be supported in the future.
• Special care for Laser B eam s: Spec ial care should be used when DLP projectors are us ed in the same room as h i
gh pow er
laser equipment. Direct or indirect hitting of a laser beam on to the lens can severely da mage the Digital Mirror Devices
TM
in
which case there is a loss of warranty.
• Never place the projector in direct sunlight. Sunlight on the lens can severely dama ge the Digital Mirror Devices
TM
in which
case there is a loss of warranty.
• Save the original shipping carton and packing material. They will come in handy if you ever have to ship your equipment. For
maximum protection, repack your set as it w as originally packed at the factory.
• Disconnect the power to the projector before cleaning. D o not use liquid cleaners or aerosol cleaners. Use a damp cloth for
cleaning. Never use strong so lvents, s uch as thinner or benzine, or, patrol, or abrasive cleaners, since these will damage the
cabinet. Stubborn stains m ay be removed with a cloth lightly dampe ned with m ild detergent solution.
• To ensure the highest o ptical performance and resolution, the projection lenses are specially treated with an anti-reflective
coating, therefore, avoid touching the lens. To rem ove dust on the lens, use a so ft dry cloth. Do not use a damp cloth, detergent
solution, or thinner.
• Rated maximum amb ient temperature, t
a
= 35°C (95°F).
• The lamp house shall be r eplaced if it has bec ome d amaged o r thermally deformed.
• Do not stack DP2K-E series projectors.
On servicing
• Do not attempt to service this pr oduct yourself, as o pening or removing covers may expose you to dangerous voltage p otentials
and r isk of electric shock.
• Refer all servicing to qualified s ervice personnel.
• Attempts to alter the factory-set internal controls or to change other control settings not specially discussed in this manual c an
lead to per manent dam age to the projector and cancellation of the w arranty.
• Remove all po wer from the projector and refer s ervicing to qualified service technicians under the following conditions:
- When the power cord o r plug is da maged or frayed.
- If liquid has been spilled into the equipment.
- If the product has been exposed to rain or water.
- If the p roduct does not o perate normally wh en the operating instructions ar e followed. Adjust only those controls that are
covered by the operating instructions since improper adjustmen
t of the other controls may result in dam age and will often
require extensive work by a qualified technician to restore the pr oduct to normal operation.
- If the product has been dropped or the cabinet ha s been dam aged.
- If the product exhibits a distinct change in per formance, indicating a need for service.
• Replacement pa rts: W hen replacement parts are required, be sure the service technician has used original B arco replacement
parts or authorized replacement parts which have the same cha racteristics as the Barco original part. Unauthorize d substitu-
tions may result in degraded performance and reliability, fire, electric shock or other h azards. Unauthorized substitutions may
void wa rra nty.
• Safety check: Upon c ompletion of any s ervice or repairs to this projector, ask the service technician to perform safety c hecks
to determine that the product is in proper operating c
ondition.
• Possible explosion hazard: Always keep in mind the caution below:
To prevent battery explosion
• Danger of explosion if battery is incorrectly installed.
• Replace only with the same or equivalent type recomm ended by the manufacturer.
• For disposal of used batteries, always consult federal, state, local a nd provincial hazardous waste disposal rules and regulations
to ensure proper disposal.
R5906693 DP2K-E SERIES 19/06/2015
9
To Next Page
Loading...
Need help?
General
