Lenze 8400 StateLine C User Manual

Firmware ≤ 11.00 - DMS 8.0 EN - 10/2011 L 407
8400 StateLine C | Reference manual
Diagnostics & error management
Error messages of the operating system
9.9.5 Short overview (A-Z)
The table below contains all error messages of the controller operating system in
alphabetical order.
 Tip!
If you click the cross-reference in the first column, "Error number", you will reach
the detailed description of the respective error message in the following chapter,
"Cause & possible remedies
". ( 409)
 Note!
For the sake of legibility, the Logbookand C00165 display the error number with
the following syntax:
[Error type].[Error subject area no.].[Error ID]
In this documentation, "xx", a wildcard, stands for the error type since it is
configurable for many error messages.
Error number Error message Response
(Lenze setting)
can be set in CAN Emergency
Error Code
32 bits 16 bits
hex
16 bits
dec
xx.0125.00001 0x1901 6401 An01: AIN1_I < 4 mA TroubleQuickStop C00598/1 0xF000
xx.0131.00006
0x1f06 7942 CA06: CAN CRC error No Reaction C00592/1 0x8000
xx.0131.00007
0x1f07 7943 CA07: CAN bus warn No Reaction C00592/3 0x8000
xx.0131.00008
0x1f08 7944 CA08: CAN Bus Stopped No Reaction C00592/4 0x8000
xx.0131.00011
0x1f0b 7947 CA0b: CAN HeartBeatEvent No Reaction C00592/5 0x8130
xx.0131.00015
0x1f0f 7951 CA0F: CAN control word Fault C00594/2 0xF000
xx.0127.00002
0x1b02 6914 CE04: MCI communication error No Reaction C01501/1 0x7000
xx.0127.00015
0x1b0f 6927 CE0F: MCI control word Fault C00594/2 0xF000
xx.0135.00001
0x2301 8961 CE1: CAN RPDO1 No Reaction C00593/1 0x8100
xx.0135.00002
0x2302 8962 CE2: CAN RPDO2 No Reaction C00593/2 0x8100
xx.0135.00003
0x2303 8963 CE3: CAN RPDO3 No Reaction C00593/3 0x8100
xx.0131.00000
0x1f00 7936 CE4: CAN Bus Off No Reaction C00592/2 0x8000
xx.0184.00064
0x5440 21568 Ck16: Time overflow manual control Fault -
xx.0140.00013
0x280d 10253 Cl01: Module missing/incompatible No Reaction C01501/2 0x7000
xx.0135.00004
0x2304 8964 CP04: CAN RPDO4 No Reaction C00593/4 0x8100
xx.0145.00035
0x2d23 11555 dF10: AutoTrip Reset Fault C00189 0xF000
xx.0145.00014
0x2d0e 11534 dF14: SW/HW invalid Fault -
xx.0145.00024
0x2d18 11544 dF18: BU RCOM error Fault - 0x6100
xx.0145.00033
0x2d21 11553 dF21: BU Watchdog Fault - 0x6100
xx.0145.00034
0x2d22 11554 dF22: CU watchdog Fault - 0x6100
xx.0145.00025
0x2d19 11545 dF25: CU RCOM error Fault - 0x6100
xx.0145.00026
0x2d1a 11546 dF26: Appl. watchdog No Reaction C00580/1 0x6200
xx.0145.00050
0x2d32 11570 dF50: Retain error Fault - 0x6100
xx.0145.00051
0x2d33 11571 dF51: CuCcr error Fault - 0x6100
xx.0400.00009
0x1a09 6665 dH09: EEPROM power section Fault - 0x5530
xx.0400.00016
0x1a10 6672 dH10: Fan failure Warning C00566 0x5000
xx.0400.00104
0x1a68 6760 dH68: Adjustment data error CU Fault - 0x5530
xx.0400.00105
0x1a69 6761 dH69: Adjustment data error BU Fault - 0x5530
xx.0123.00094
0x175e 5982 FC01: Switching frequency reduction No Reaction C00590 0x2000
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: info@clrwtr.com

Lenze 8400 StateLine C Specifications

General

Brand	Lenze
Model	8400 StateLine C
Category	Inverter Drive
Language	English