MTS Systems FlexTest IIm User Manual

MTS 793 Controller Hardware
FlexTest IIm Controller Connections
172
Hydraulic Connections
You must connect your external hydraulic equipment to the Model
497.05 Hydraulic Control Panel. The FlexTest IIm hardware supports
control of up to four hydraulic stations simultaneously.
S
TOP
H
a
z
a
r
d
o
u
s
v
o
l
t
a
g
e
.
C
a
n
c
a
u
s
e
s
e
v
e
r
e
i
n
j
u
r
y
o
r
d
e
a
t
h
.
W
A
R
N
I
N
G
T
u
r
n
o
f
f
m
a
i
n
p
o
w
e
r
a
n
d
a
l
l
m
u
l
t
i
p
l
e
p
o
w
e
r
s
o
u
r
c
e
s
b
e
f
o
r
e
o
p
e
n
i
n
g
p
a
n
e
l
.
Hydraulic Power Unit
HSM
HSM
HSM
J25
HSM
J28C J28B
J28A
J28D
FlexTest IIm Hydraulic Connections
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

MTS Systems FlexTest IIm Specifications

General

Model	FlexTest IIm
Data Acquisition	Yes
Resolution	24-bit
Input Range	±10 V
Input Voltage	±10 V
Interface	Ethernet
Control Mode	Closed-loop
Operating Temperature	0 to 50 °C
Storage Temperature	-20°C to 70°C

Summary

Technical Support

How to Get Technical Support

Guidance on contacting MTS for technical assistance via various methods.

Before You Contact MTS

Information to prepare before contacting MTS for efficient support.

Preface

Before You Begin

Important introductory information and safety precautions before system use.

Chapter 1 Introduction

FlexTest GT Controllers

Overview of hardware components and specifications for FlexTest GT.

FlexTest SE Controllers

Overview of hardware components and specifications for FlexTest SE.

FlexTest IIm Controllers

Overview of hardware components and specifications for FlexTest IIm.

Chapter 2 Installation

Installing the 493.10 Chassis (FTGT)

Step-by-step guide for installing the 493.10 Chassis (FTGT).

Installing the 493.02 Chassis (FlexTest SE)

Step-by-step guide for installing the 493.02 Chassis (FlexTest SE).

Installing 497/498 Electronics (FTIIm)

Guide for installing 497/498 electronics into the FTIIm controller.

Chapter 3 FlexTest GT Controller Connections

Cable Information

Information on cable part numbers, specifications, and types.

Module Connections

Details on connecting I/O Carrier, sensors, valves, ADDA II, and encoders.

Power, Control, and Interlock Connections

Information on HPU, HSM, E-stop, interlock, and station connections.

System Integration Connections

Guides for workstation, remote station, and external controller connections.

Chapter 4 FlexTest IIm Controller Connections

Controller and System Connections

Details on workstation, serial, hydraulic, and HSM connections.

Signal and Interlock Connections

Information on analog I/O, digital I/O, interlocks, and encoder/Temposonics.

External Controller Integration

Guides for connecting and programming external controllers and Eurotherm units.

Chapter 5 FlexTest SE Controller Connections

Cabling Overviews

Diagrams illustrating standalone, automated, and multiple controller cabling.

Module and I/O Connections

Details on I/O carrier, sensor, valve, analog, encoder, and system I/O connections.

Power, Control, and Interlock Connections

Information on HPU, HSM, E-stop, interlock, and digital I/O connections.

System Integration and External Controller Connections

Guides for workstation, RSC, and Eurotherm connections.

Appendix A Hydraulic Configurations

Converter Box and HPU Connections

Connecting chassis to converter box and HPU.

Hydraulic Pump Configurations

Diagrams showing chassis connections to hydraulic power units.

Appendix B Chassis Maintenance

Chassis Maintenance

Procedures for maintaining the MTS controller chassis.

Cleaning the Air Filter

Steps for cleaning or replacing the air filter for cooling.

Appendix D Optional Station Configurations

Optional Station Configurations

How to configure for optional six or eight stations.

6-Station Configuration

Details on configuring a 6-station setup.

8-Station Configuration

Details on configuring an 8-station setup.