Omron E5*C Series User Manual

Index-4
E5@C-T Digital Temperature Controllers User’s Manual (H185)
Hysteresis (Heating) ..............................................6-38
Initial Setting/Communications Protect ....................6-4
Input Digital Filter ................................................... 6-87
Input Type .................................................... 6-56, A-23
input type ...............................................................4-18
Integral Time ..........................................................6-36
Integral Time (Cooling) ..........................4-21, 5-9, 6-37
Integral/Derivative Time Unit ........................6-37, 6-86
Integrated Alarm Assignment .......................5-23, 6-99
LBA Band .....................................................5-28, 6-96
LBA Detection Time ......................................5-28, 6-95
LBA Level .....................................................5-28, 6-96
LCT Cooling Output Minimum ON Time .............. 6-104
Leakage Current 1 Monitor ....... 6-13, 6-31, 6-47, 6-49,
6-63, 6-64, 6-65, 6-76, 6-77, 6-78
Leakage Current 2 Monitor ...........................6-14, 6-32
Limit Cycle MV Amplitude .............................4-51, 6-87
Loop Burnout Alarm (LBA) .................................... 5-27
Manual Control Level ............................................. 5-33
Manual MV Initial Value .........................................6-93
Manual MV Limit Enable ......................................6-101
Manual Output Method ..........................................6-92
Manual Reset Value ............................................... 6-38
Minimum Output ON/OFF Band ..........................6-104
Monitor/Setting Item 1 to 5 .................................. 6-106
Monitor/Setting Item Display 1 to 5 ........................ 6-51
Move to Advanced Function Setting Level .............6-79
Move to Calibration Level ....................................6-110
Move to Protect Level .............................................. 6-3
Move to Protect Level Time ................................... 6-90
Move to the Protect Level ...................................... 5-19
Moving Average Count ...................................5-3, 6-88
MV (Manual MV) .................................................... 6-53
MV at Error ............................................................6-39
MV at PV Error ......................................................5-68
MV at Reset ........................................................... 5-67
MV Change Rate Limit .................................5-72, 6-41
MV Lower Limit ......................................................6-40
MV Monitor (Cooling) .............................................6-15
MV Monitor (Heating) ............................................ 6-14
MV Upper Limit ......................................................6-40
Operation/Adjustment Protect ..................................6-4
Parameter Initialization .......................................... 6-82
Parameter Mask Enable ..........................................6-5
password ............................................................... 5-19
Password to Move to Protect Level 6-6, 6-13, 6-14, 6-15
PF Setting ...................................................6-51, 6-105
PID * LBA detection time .......................................6-49
PID * MV lower limit ............................................... 6-48
PID automatic selection range upper limit ............. 6-49
PID MV upper limit ................................................. 6-48
PID ON/OFF ..........................................................6-63
PID ON/OFF parameter .........................................4-75
Position Proportional Dead Band ..................5-80, 6-41
Process Value Input Shift ......................................... 5-3
Process Value Slope Coefficient .............................. 5-3
Process Value/Set Point 1 .......................................6-8
Process Value/Set Point 2 .......................................6-8
Proportional Band ..................................................6-36
Proportional Band (Cooling) ..................4-21, 5-9, 6-37
Protocol Setting ................................................... 6-111
PV Rate of Change Calculation Period .......4-60, 6-102
PV Status Display Function ................................. 6-108
PV/MV (Manual MV) .............................................. 6-53
PV/SP Display Selection ......................................... 6-8
PV/SP No. 1 Display Selection ............4-76, 6-8, 6-107
PV/SP No. 2 Display Selection ............4-76, 6-8, 6-107
RT ........................................................6-94, 6-95, 6-96
RT (Robust Tuning) ................................................ 6-93
Scaling Lower Limit ............................................... 6-57
Scaling Upper Limit ............................................... 6-57
Set Point Lower Limit ............................................. 5-16
Set Point Upper Limit ............................................. 5-16
Setting Change Protect ........................................... 6-5
SP Lower Limit ...................................................... 6-58
SP Mode ................................................................ 6-28
SP Tracking .......................................................... 6-100
SP Upper Limit ...................................................... 6-58
Standard or Heating/Cooling ................................. 6-64
Standby Sequence Reset ...................................... 6-83
SV Status Display Function ................................. 6-109
Temperature Unit ................................................... 6-57
Transfer Output Lower Limit ................................... 6-73
Transfer Output Signal ........................................... 6-71
Transfer Output Type ....................................5-34, 6-72
Transfer Output Upper Limit ................................... 6-73
Work Bit 1 to 8 OFF Delay ..................................... 6-43
Work Bit 1 to 8 ON Delay ....................................... 6-43
password ............................................................5-19, 5-20
setting .................................................................... 5-20
PF Key (S Key) .................. 3-7, 3-8, 5-19, 5-33, 5-74, 6-5
PF setting .................................................................... 5-74
PID constants .............................................................. 4-49
PID control .................................................................. 4-21
position-proportional control ........................................ 5-79
Potentiometer Input ..................................................... 2-21
potentiometer input error ....................................5-31, 5-68
potentiometer input error
(Position-proportional Models Only) .........................A-14
power supply ............................................................... 2-16
process value/set point 1 ............................................. 4-76
process value/set point 2 ............................................. 4-76
proportional action ....................................................... 4-54
proportional band ........................................................ 4-55
Protect Level ........................................................6-3, A-31
protection .................................................................... 5-18
Initial Setting/Communications Protect .................. 5-19
Operation/Adjustment Protect ............................... 5-18
PF Key Protect ....................................................... 5-19
Setting Change Protect ......................................... 5-19
PV change rate alarm ................................................. 4-60
PV status display ......................................................... 5-77
R
ratings ...........................................................................A-2
registering calibration data ............................................ 7-2
resistance thermometer calibration ............................... 7-7

Omron E5*C Series Specifications

General

Brand	Omron
Model	E5*C Series
Category	Controller
Language	English