Ricoh G104 User Manual

SERVICE MODE TABLE
G104 5-10 SM
5.2.3 ENGINE SERVICE MODE
SP1-XXX (Feed)
[Lead Edge Reg.] Leading Edge Registration
(Tray or By-pass, Paper Type, Process Speed)
Paper Type ->N: Plain paper 1, N2 or Normal 2: Plain paper 2, Thick2: Thick
paper 2 (see the Specifications table for details on these paper weights)
Process Speed: LS: Low speed, RS: Regular speed
1001
Adjusts the leading edge registration. This SP changes the registration clutch
operation timing for each mode.
+value sets the registration start timing earlier.
-value sets the registration start timing later.
NOTE: The value of the normal paper in RS is the standard value. The values
of papers other than normal are added to the value of the normal paper
in RS.
1001 001 Tray 1: Normal: LS *EGB
[-10.0 to 10.0 / 0.0 / 0.1 mm/step]
1001 002 Tray 1: Normal: RS *EGB [-10.0 to 10.0 / -3.0 / 0.1 mm/step]
1001 003 Tray 1: Thick *EGB [-10.0 to 10.0 / 1.5 / 0.1 mm/step]
1001 004 Tray 1: OHP *EGB [-10.0 to 10.0 / 0.0 / 0.1 mm/step]
1001 005 Tray 2: Normal: LS *EGB [-10.0 to 10.0 / 0.0 / 0.1 mm/step]
1001 006 Tray 2: Normal: RS *EGB [-10.0 to 10.0 / -3.0 / 0.1 mm/step]
1001 007 Tray 2: Thick *EGB [-10.0 to 10.0 / 1.5 / 0.1 mm/step]
1001 008 Tray 2: OHP *EGB [-10.0 to 10.0 / 0.0 / 0.1 mm/step]
1001 009 Tray 3: Normal: LS *EGB [-10.0 to 10.0 / 0.0 / 0.1 mm/step]
1001 010 Tray 3: Normal: RS *EGB [-10.0 to 10.0 / -3.0 / 0.1 mm/step]
1001 011 Tray 3: Thick *EGB [-10.0 to 10.0 / 1.5 / 0.1 mm/step]
1001 012 Tray 3: OHP *EGB [-10.0 to 10.0 / 0.0 / 0.1 mm/step]
1001 013 By-pass: N: LS *EGB [-10.0 to 10.0 / 0.0 / 0.1 mm/step]
1001 014 By-pass: N: RS *EGB [-10.0 to 10.0 / -3.0 / 0.1 mm/step]
1001 015 By-pass: Thick *EGB [-10.0 to 10.0 / 1.5 / 0.1 mm/step]
1001 016 By-pass: OHP *EGB [-10.0 to 10.0 / 0.0 / 0.1 mm/step]
1001 017 Duplex: Normal: LS *EGB [-10.0 to 10.0 / 0.0 / 0.1 mm/step]
1001 018 Duplex: Normal: RS *EGB [-10.0 to 10.0 / -3.0 / 0.1 mm/step]
1001 019 Duplex: Thick *EGB [-10.0 to 10.0 / 1.0 / 0.1 mm/step]
1001 020 Duplex: N2: LS *EGB [-10.0 to 10.0 / 1.0 / 0.1 mm/step]
1001 021 Duplex: N2: RS *EGB [-10.0 to 10.0 / 1.0 / 0.1 mm/step]
1001 022 Tray 1: Normal 2: LS *EGB [-10.0 to 10.0 / 1.0 / 0.1 mm/step]
1001 023 Tray 1: Normal 2: RS *EGB [-10.0 to 10.0 / 1.0 / 0.1 mm/step]
1001 024 Tray 1: Thick 2 *EGB [-10.0 to 10.0 / 1.5 / 0.1 mm/step]
1001 025 Tray 1: Thin: LS *EGB [-10.0 to 10.0 / 0.0 / 0.1 mm/step]
1001 026 Tray 1: Thin: RS *EGB [-10.0 to 10.0 / 0.0 / 0.1 mm/step]
1001 027 Tray 1: Special *EGB [-10.0 to 10.0 / 1.5 / 0.1 mm/step]
1001 028 Tray 2: Normal 2: LS *EGB [-10.0 to 10.0 / 1.0 / 0.1 mm/step]
1001 029 Tray 2: Normal 2: RS *EGB [-10.0 to 10.0 / 1.0 / 0.1 mm/step]
1001 030 Tray 2: Thick 2 *EGB [-10.0 to 10.0 / 1.5 / 0.1 mm/step]
1001 031 Tray 2: Thin: LS *EGB [-10.0 to 10.0 / 0.0 / 0.1 mm/step]
1001 032 Tray 2: Thin: RS *EGB [-10.0 to 10.0 / 0.0 / 0.1 mm/step]
1001 033 Tray 2: Special *EGB [-10.0 to 10.0 / 1.5 / 0.1 mm/step]
1001 034 Tray 3: Normal 2: LS *EGB [-10.0 to 10.0 / 1.0 / 0.1 mm/step]
1001 035 Tray 3: Normal 2: RS *EGB [-10.0 to 10.0 / 1.0 / 0.1 mm/step]
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA

Ricoh G104 Specifications

General

Brand	Ricoh
Model	G104
Category	All in One Printer
Language	English