Siemens SINAMICS G120 User Manual

Connector/Binector (BICO)-Parameters
Parameters
1-489
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU230P-2 Parameter Manual (LH9), 01/2011
r11073 CO: Free tec_ctrl 0 system deviation / Ftec0 sys dev
p11091 CO: Free tec_ctrl 0 limit maximum / Ftec0 lim max
p11092 CO: Free tec_ctrl 0 limit minimum / Ftec0 lim min
r11094 CO: Free tec_ctrl 0 output signal / Ftec0 out_sig
r11160 CO: Free tec_ctrl 1 setpoint after ramp-function generator / Ftec1 setp aft RFG
r11172 CO: Free tec_ctrl 1 actual value after limiter / Ftec1 act v af lim
r11173 CO: Free tec_ctrl 1 system deviation / Ftec1 sys dev
p11191 CO: Free tec_ctrl 1 limit maximum / Ftec1 lim max
p11192 CO: Free tec_ctrl 1 limit minimum / Ftec1 lim min
r11194 CO: Free tec_ctrl 1 output signal / Ftec1 out_sig
r11260 CO: Free tec_ctrl 2 setpoint after ramp-function generator / Ftec2 setp aft RFG
r11272 CO: Free tec_ctrl 2 actual value after limiter / Ftec2 act v af lim
r11273 CO: Free tec_ctrl 2 system deviation / Ftec2 sys dev
p11291 CO: Free tec_ctrl 2 limit maximum / Ftec2 lim max
p11292 CO: Free tec_ctrl 2 limit minimum / Ftec2 lim min
r11294 CO: Free tec_ctrl 2 output signal / Ftec2 out_sig
r20095 CO: ADD 0 output Y / ADD 0 output Y
r20099 CO: ADD 1 output Y / ADD 1 output Y
r20103 CO: SUB 0 difference Y / SUB 0 difference Y
r20107 CO: SUB 1 difference Y / SUB 1 difference Y
r20111 CO: MUL 0 product Y / MUL 0 product Y
r20115 CO: MUL 1 product Y / MUL 1 product Y
r20119[0...2] CO: DIV 0 quotient / DIV 0 quotient
r20124[0...2] CO: DIV 1 quotient / DIV 1 quotient
r20129 CO: AVA 0 output Y / AVA 0 output Y
r20134 CO: AVA 1 output Y / AVA 1 output Y
r20220 CO: NSW 0 output Y / NSW 0 output Y
r20225 CO: NSW 1 output Y / NSW 1 output Y
r20231 CO: LIM 0 output Y / LIM 0 output Y
r20239 CO: LIM 1 output Y / LIM 1 output Y
r20247 CO: PT1 0 output Y / PT1 0 output Y
r20253 CO: PT1 1 output Y / PT1 1 output Y
r20261 CO: INT 0 output Y / INT 0 output Y
r20286 CO: DIF 0 output Y / DIF 0 output Y
r20309 CO: ADD 2 output Y / ADD 2 output Y
r20373 CO: PLI 0 output Y / PLI 0 output Y
r20379 CO: PLI 1 output Y / PLI 1 output Y
r31024 CO: Multi-zone control setpoint output / Zone_ctrl set outp
r31027 CO: Multi-zone control actual-value output / Zon_ctrl act outp
1.4.5 Connector/Binector Output Parameters
Product: SINAMICS G120, Version: 4402100, Language: eng, Type: CO/BO
r0046.0...31 CO/BO: Missing enable sig / Missing enable sig
r0050.0...1 CO/BO: Command Data Set CDS effective / CDS effective
r0051.0...1 CO/BO: Drive Data Set DDS effective / DDS effective
r0052.0...15 CO/BO: Status word 1 / ZSW 1
r0053.0...11 CO/BO: Status word 2 / ZSW 2
r0054.0...15 CO/BO: Control word 1 / STW 1
r0055.0...15 CO/BO: Supplementary control word / Suppl STW
r0056.0...15 CO/BO: Status word, closed-loop control / ZSW cl-loop ctrl
r0056.0...13 CO/BO: Status word, closed-loop control / ZSW cl-loop ctrl
r0722.0...12 CO/BO: CU digital inputs, status / CU DI status

Siemens SINAMICS G120 Specifications

General

Power Range	0.37 kW to 250 kW
Output Voltage	0 V to Input Voltage
Frequency Range	0 Hz to 650 Hz
Enclosure Rating	IP20, IP21, IP55
Control Modes	V/f control, vector control, servo control
Protection Features	Overvoltage, undervoltage, short circuit
Communication Interfaces	PROFIBUS, PROFINET, Modbus RTU
Operating Temperature	-10°C to +50°C
Cooling Method	Air cooling
Input Voltage	200 V to 240 V, 380 V to 480 V, 500 V to 690 V