Table of contents
8.14 Replacing of the notch filter ........................................................................................................154
8.15 Adjusting the notch filter............................................................................................................156
8.16 Cleaning the Prism exit side .......................................................................................................158
9. Convergence ..................................................................................................... 159
9.1 Convergence controls ..............................................................................................................160
9.2 Preparing the convergence adjustment. . . . . .......................................................................................162
9.3 Red on Blue convergence......................................................................................................... .163
9.4 Green on Blue convergence .......................................................................................................165
10. Integrator rod .................................................................................................... 167
10.1 Introduction .........................................................................................................................168
10.2 Rod diagnostic ......................................................................................................................169
10.3 Removal of the integrator rod ......................................................................................................170
10.4 Installation of a new integrator rod.................................................................................................173
10.5 Adjusting the integrator rod ........................................................................................................177
11. Lenses and Lens holder ....................................................................................... 179
11.1 Available lenses ....................................................................................................................180
11.2 Lens selection ......................................................................................................................181
11.3 Lens removal .......................................................................................................................182
11.4 Lens installation ....................................................................................................................183
11.5 Cleaning the lens . . . ................................................................................................................185
11.6 Remove the lens holder............................................................................................................186
11.7 Install the lens holder...............................................................................................................189
11.8 Scheimpflug adjustment............................................................................................................192
11.9 Replacement of the Ve rtical Shift stepper motor ..................................................................................196
11.10 Replacement of the Horizontal Shift stepper m otor ...............................................................................198
11.11 First Placement of the Inner D ust Rubber . . .......................................................................................200
11.12 Replacement of the Inner Dus t Rubber. . . . . .......................................................................................204
12. Card Cage......................................................................................................... 207
12.1 F an c ontroller board ................................................................................................................208
12.2 Integrated Cinema Pr ocessor (ICP) board . .......................................................................................209
12.3 HD-SDI board + link decryptor .....................................................................................................210
12.4 Cinema c ontroller board ............................................................................................................211
12.5 Rem oving a board in the card cage................................................................................................213
12.6 Inserting a board in the card cage .................................................................................................214
12.7 Replace ment of the RTC battery of the ICP board ................................................................................215
12.8 Battery replacement on the Cinema Controller Board ............................................................................217
12.9 Removing the button unit...........................................................................................................219
12.10 Installation of the button unit .......................................................................................................222
12.11 Replacement of the Button module (first generation Keypad) ....................................................................223
12.12 Replacem ent of the K eypad (first generation Keypad). . ..........................................................................226
12.13 Replacem ent of the K eypad assembly (second generation K eypad) . . ...........................................................230
12.14 Replacem ent of the s ignal bac k plane .............................................................................................231
12.15 Replacement of the Link Decryptor................................................................................................243
12.16 Authorization to clear security warning on the projector ..........................................................................245
12.17 Replacement of the Status Light...................................................................................................246
13. Software update via Communicator (DC update companion)...... .... .... .... .... .... .... ...... .... ... 247
13.1 So ftware upgrade, launch DC update c ompan ion .................................................................................248
13.2 So ftware upgrade, projector, ICMP or touch panel................................................................................251
13.3 ICP software upgrade ..............................................................................................................255
13.4 Link decryptor software update . . . .................................................................................................258
13.5 Update logging......................................................................................................................260
14. Communicator touch panel.................................................................................... 261
14.1 Introduction .........................................................................................................................262
14.2 Installing the touch panel interface.................................................................................................264
14.3 Repos ition the touch panel interface ...............................................................................................266
15. Power input.. .... .... .... .... .......... .... .... .... .... .... .... .... .... .... ...... .... .... .... .... .... .... .... .... . 267
15.1 Introduction .........................................................................................................................268
15.2 G etting a ccess to the Mains Input com ponents ...................................................................................269
15.3 Replace ment of the mains O N/OFF switch . .......................................................................................271
15.4 Replace ment of the mains input filter..............................................................................................273
15.5 Closing the M ains Input compartment .............................................................................................275
16. Switched mode power supply.... .... .... .... .... .... .... .... .... .... .... .... .... .......... .... .... .... .... ... 279
16.1 Diagnos tic LEDs on the SMP S.....................................................................................................280
16.2 Replace ment of the Switched Mode Power Supply ...............................................................................281
17. Lamp power supply .... .... .... .... .... ...... .... .... .... .... .... .... .... .... .... .......... .... .... .... .... .... . 283
17.1 Introduction .........................................................................................................................284
17.2 LPS diagnostic LED’s ..............................................................................................................285
17.3 Rem oval of the LPS m odule .......................................................................................................287
2
R5905043 DP2K-12C/11CX 19/02/2018
To Next Page
Loading...
Need help?
General