Pioneer PDP-433CMX User Manual

171
Integrator Mode
23) Simple checking of internal temperature
This function enables the unit’s internal temperature to be
easily checked using the level meter indicator.
When the indicator is green = internal temperature is normal.
When the indicator is yellow or red = internal temperature is slightly high. Turn OFF the power supply once,
confirm installation status immediately, and then use air conditioning or
the like to counteract the heat radiation.
When checking the internal temperature, conduct aging thoroughly, just as before making adjustments.
(Minimum: 30 min. with a 100% white signal.)
The same applies to checking the effect of countermeasures to heat radiation.
For more details, see Chapter 3, “Installation site requirements”
1 Enter integrator mode.
(See 5.4.1, “About the integrator mode.”)
The set ID will be displayed on the upper right where the
“– –“ mark is.
Select OPTION.
2 Use TEMPERATURE to check the internal temperature.
Temperature can also be checked by pushing the DISPLAY
button for 2 seconds or more in display call.
(See 5.2.1, “about normal operating mode”)
Screen 1
Screen 2
CAUTION
]
]
O
D:
:
:
:
:
:
:
:
:
AA
S D
E
M
T
T
B
O
U
R
NO
FF
OFF
OF/F
OFF
OFF
ON
E
R
LUAKSF
S
L
E
I
DI
M
AKSM
OEDM
OEDM
OEDMOEDM
AKSMLOT
E
N
TO
R
I
O
BRR
C
ENSE
R
I
C
V
OLO
R
48 B 00
128
/ 1
1
28 128 /
1
0 / 0 .W/
PS
INPUT1
––
INTEGRATOR MENU
CHANGE EXITMENU SET SELECT
PICTURE WHITE BAL SCREEN SET UP OPTION
:OFFOEDMROMRRI
OTLROCFNAN
AEMNOTMINOR AMPSAL
INPUT1
––
INTEGRATOR MENU
CHANGE EXITMENU SET SELECT
T
H
:
:
0
CH
H
EPERATUREM
OUR METER
000 0
I:
:
––DNOSET.
AOTU:
PICTURE WHITE BAL SCREEN SET UP OPTION
24) Checking the accumulated ON time
This function displays the accumulated time (in 1-hour units) for which the unit has been receiving power.
The accumulated time does not include the time when the unit is in standby mode.
1 Enter integrator mode.
(See 5.4.1, “About the integrator mode.”)
The set ID will be displayed on the upper right where the
“– –“ mark is.
Select OPTION.
2 Use HOUR METER to check the accumulated ON time.
The accumulated ON time can also be checked by pushing
the DISPLAY button for 2 seconds or more in display call.
(See 5.2.1, “About normal operating mode.”)
Screen 1
Screen 2
CAUTION
]
]
:OFFOEDMROMRRI
OTLROCFNAN
AEMNOTMINOR AMPSAL
INPUT1
––
INTEGRATOR MENU
CHANGE EXITMENU SET SELECT
T
H
:
:
0
CH
H
EPERATUREM
OUR METER
000 0
I:
:
––DNOSET.
AOTU:
PICTURE WHITE BAL SCREEN SET UP OPTION
O
D:
:
:
:
:
:
:
:
:
AA
S
D
E
M
T
T
B
O
U
R
NO
FF
OFF
OF/F
OFF
OFF
ON
E
R
LUAKSF
S
L
E
I
DI
M
AKSM
OEDM
OEDM
OEDMOEDM
AKSMLOT
E
N
TO
R
I
O
BRR
C
ENSE
R
I
C
V
OLO
R
48 B 00
128
/ 1
1
28 128 /
1
0 / 0 .W/
PS
INPUT1
––
INTEGRATOR MENU
CHANGE EXITMENU SET SELECT
PICTURE WHITE BAL SCREEN SET UP OPTION

Pioneer PDP-433CMX Specifications

General

Brand	Pioneer
Model	PDP-433CMX
Category	Monitor
Language	English