Name: Barco DP2K SLP Series
Brand: Barco
Rating: 4 (1 reviews)

To Next Page

To Previous Page

9. Starting up

9. STARTING UP

About this chapter

This chapter contains the switch ON an d switch OFF procedures of your DP2K SLP -series. These proc edures highlight all important

points to be checked prior to sw itching the projector O N. This is to ensure a safe startup of the projector.

Overview

• Switching the DP2K S LP-series ON

• Switching the D P2K SLP-series OFF

R5906847 DP2K SLP SERIES 02/06/2017

Default Chapter5
- Table of Contents5
Safety7
- General Considerations8
- Important Safety Instructions10
- Product Safety Labels13
- High Brightness Precautions: Hazard Distance (HD)14
- HD for Fully Enclosed Projection Systems16
- HD in Function of Modifying Optics17
Getting Started19
- Installation Requirements20
- Unpacking the Projector22
- Initial Inspection24
- Communicator PC Version25
- Commander & Web Commander26
Installation Process27
- Installation Process Overview28
- Software Upgrade29
- Starting up and Adjusting the System30
Physical Installation31
- Positioning the DP2K SLP-Series Projector at Port Window32
- Connecting the Projector with the Power Net35
Lenses & Lens Selection37
- Available Lenses38
- Lens Selection39
- Lens Installation40
- Lens Removal41
- Lens Shift, Zoom & Focus42
Input & Communication45
- Introduction46
- Local Keypad47
- Projector Status49
- Integrated Cinema Processor (ICP)50
- HD-SDI Input Module (Optional)51
- Integrated Media Block/Server (Optional)54
- Cinema Controller55
Icmp57
- ICMP Introduction58
- Icmp Hdd60
- ICMP Communication Ports61
- ICMP Source Input Ports63
- ICMP Displayport Speciﬁcations64
- ICMP SDI Speciﬁcations66
- ICMP HDMI 2.0 Speciﬁcations70
- ICMP HDMI 1.4 Speciﬁcations73
- ICMP Status Leds75
- ICMP HDD Status Leds76
- ICMP Device Certiﬁcate78
- ICMP Conﬁguration Via Communicator80
- ICMP Reset81
- Obtaining the Barco ICMP Certiﬁcate82
- Removing a HDD from the ICMP83
- Installing a HDD into the ICMP84
Communicator Touch Panel87
- Communicator Touch Panel88
- Installing the Touch Panel Interface90
- Repositioning the Touch Panel Interface92
Starting up93
- Switching the DP2K SLP-Series on94
- Switching the DP2K SLP-Series off95
Scheimpﬂug97
- Scheimpﬂug Introduction98
- Scheimpﬂug Adjustment100
- Fixation of the Lens Holder Front Plate102
- Back Focal Length Adjustment104
Convergence109
- Convergence Controls110
- Preparing for Convergence Adjustment112
- Converging the Blue Pattern Onto the Red Pattern113
- Converging the Green Pattern Onto the Red Pattern114
- Closing off the Light Processor Compartment115
Color Calibration117
- Calibration Process118
- Color Gamut Calibration119
Preventative Maintenance Actions121
- Month Maintenance Actions122
- Month Maintenance Actions123
Maintenance Procedures125
- Check the Large Dust Filter126
- Check the Small Dust Filter128
- Vacuum Cleaning of the Dust Filters130
- Washing and Drying the Dust Filters131
- Cleaning the Lens132
- Cleaning the Exterior of the Projector133
- Authorization to Clear Security Warning on the Projector134
Removal and Installation of the Projector Covers135
- Removal of the Light Source Cover136
- Removal of the Rear Cover137
- Removal of the Top Cover138
- Removal of the Left Side Cover139
- Removal of the Top Cover Plate of the Light Processor Compartment140
- Removal of the Side Cover Plate of the Light Processor Compartment142
- Installation of the Side Cover Plate of the Light Processor Compartment143
- Installation of the Top Cover Plate of the Light Processor Compartment144
- Installation of the Left Side Cover145
- Installation of the Top Cover146
- Installation of the Rear Cover147
- Installation of the Light Source Cover148
Speciﬁcations149
- Speciﬁcations of the DP2K-8SLP Series150
- Speciﬁcations of the DP2K-10SLP Series151
- Dimensions of the DP2K SLP-Series Projector152
- Dimensions of the Universal Pedestal153
- Technical Regulations154
- A.5 Technical Regulations154
Pin Conﬁgurations155
- About General Purpose Inputs & Outputs (GPIO)156
- Pin Conﬁgurations of the Cinema Controller Communication Ports158
- Pin Conﬁgurations of the ICMP Communication Ports159
Environmental Information163
- Disposal Information164
- C.1 Disposal Information164
- China Rohs Compliance165
- Taiwan Rohs Compliance167
- Turkey Rohs Compliance168
- Hazards169
- C.5 Hazards169
- Production Address170
- C.6 Production Address170
- Contact Information171
- C.7 Contact Information171
Index173

Barco DP2K SLP Series User Manual

Table of Contents

Other manuals for Barco DP2K SLP Series

Questions and Answers:

Barco DP2K SLP Series Specifications

Related product manuals

Brand	Barco
Model	DP2K SLP Series
Category	Projector
Language	English