Canon imagePROGRAF iPF680 User Manual

Cause Corrective Action
Paper has been loaded
askew, or warped paper
has been loaded.
3. If "Not finished printing. Finish printing remaining jobs?" is shown on the Display Screen, press the
OK button.
Printing will resume, starting from the page on which the error occurred.
If this error recurs after you reload the roll, remove the Roll Holder from the printer, push the roll firmly in until
it touches the Roll Holder flange, and reload the Roll Holder in the printer.
(See "Attaching the Roll Holder to Rolls.") ➔ P.370
Follow these step to reload a sheet.
1. Push the Release Lever back.
2. Load the sheet, aligning it with the guide on the right.
(See "Loading Sheets in the Printer.") ➔ P.392
3. Pull the Release Lever forward.
4. If "Not finished printing. Finish printing remaining jobs?" is shown on the Display Screen, press the
OK button.
Printing will resume, starting from the page on which the error occurred.
Insufficient paper for job
Insufficient paper for job
Cause Corrective Action
The printer has received a print job longer than the amount of roll paper left when
ManageRemainRoll in the Control Panel menu is On.
Press ▲ or ▼ to select Print, and then press the
OK button to resume printing.
However, the roll paper may run out during the
print job and you may not be able to print all of the
document.
Press ▲ or ▼ to select Change Paper, and then
press the OK button to stop printing.
Either change the printer driver Paper Source
setting or the GL2 Settings > Paper Source set-
ting in the printer menu or replace the roll with a
roll that has enough paper for the print job, and
then try printing again.
(See "Removing the Roll from the Print-
er.") ➔P.378
(See "Loading Rolls in the Printer.") ➔ P.373
Press ▲ or ▼ and select Stop Printing or press
the Stop button to stop printing.
This paper cannot be used.
This paper cannot be used.
Cause Corrective Action
Paper smaller than the printer's minimum supported
size has been loaded.
Push the Release Lever back and load paper of the correct size.
(See "Paper Sizes.") ➔P.360
Paper has been loaded that is too small to print the test
pattern for printhead adjustment or nozzle checking.
Push the Release Lever back and load unused paper of A4 size or larger.
More than one sheet may be required depending on the adjustment.
Roll printing is selected.
Roll printing is selected.
Cause Corrective Action
You have attempted to print on a roll, but
no roll is loaded.
Press ▲ or ▼ to select "Load Roll Paper", and then press the OK button. Load the roll, and
then print.
(See "Attaching the Roll Holder to Rolls.") ➔ P.370
(See "Loading Rolls in the Printer.") ➔ P.373
Press ▲ or ▼ and select Stop Printing or press the Stop button to stop printing.
iPF680
Insu󱐰cient paper for job
User's Guide
Error Message Messages regarding paper
613

Canon imagePROGRAF iPF680 Specifications

General

Color	Yes
Printing colors	Black, Cyan, Magenta, Matte black, Yellow
Print technology	Inkjet
Maximum resolution	2400 x 1200 DPI
Page description languages	GARO, HP-GL/2, HP-RTL
Media thickness	0.07 - 0.8 mm
Maximum print size	-
Maximum roll length	18 m
Media width (rolls)	254 - 609.6 mm
Media width (sheets)	203.2 - 609.6 mm
Maximum roll diameter	150 mm
Paper tray media types	Coated paper, Cut sheet, Plain paper, Roll
ISO A-series sizes (A0...A9)	A1, A2, A3
ISO B-series sizes (B0...B9)	B2, B4
Certification	RoHS
Product color	Black, Grey
Sound pressure level (printing)	47 dB
USB connector	USB Type-A
USB 2.0 ports quantity	1
Ethernet LAN data rates	10/100/1000 Base-T/TX Mbit/s
Ethernet interface type	Gigabit Ethernet
Compliance industry standards	IEEE 802.3ab, IEEE 802.3u, IEEE 802.3
Power consumption (standby)	0.5 W
Power consumption (typical)	140 W
Storage temperature (T-T)	15 - 30 °C
Operating relative humidity (H-H)	20 - 80 %
Sustainability certificates	ENERGY STAR

Weight and Dimensions

Depth	757 mm
Width	997 mm
Height	507 mm