Mitsubishi Q2ACPU User Manual

Index - 3
[I]
Index Register Processing........................App-129
Index register [Z]............................................... 4-2
Initial execution type program......................... 12-4
Initial execution WDT time.............................. 12-6
Initial processing........................................... 12-22
Installation and Removal of the Dustproof Cover
...................................................................... 19-15
Installation Environment ................................. 19-7
Installation inside the control panel ................ 20-3
Instruction List
Sequence instructions............................... App-1
Internal current consumption ............................ 4-3
Internal relay [M]............................................... 4-2
Interrupt
Interrupt counter.................................... App-121
Interrupt module.................................. 3-14,3-21
Interrupt pointer [I]......................................... 4-2
Interruption due to error detection................. 9-8
I/O assignment ................................................. 5-4
I/O control mode .................................4-1,App-127
I/O module
Fault Examples with I/O Modules ............. 22-47
Refresh processing of I/O module ............ 12-22
I/O number
Example of I/O Number Assignment............. 5-9
I/O signal
About I/O Numbers ....................................... 5-1
I/O number assignment................................. 5-2
[K]
Key input operation....................................... 10-22
Keyword Registration ..................................... 9-12
[L]
Latch clear operation ...................................... 15-6
Latch Function ................................................ 10-5
Latch relay [L] ................................................... 4-2
Latch (power failure compensation) range ....... 4-3
LED
When the "RUN" LED is flashing ................ 22-5
Flow chart used when "ERROR" LED is ON or
flashing........................................................ 22-6
Flow for actions when the "POWER" LED is
turned OFF.................................................. 22-3
Flow for actions when the "RUN" LED is turned
OFF............................................................. 22-4
When the "USER" LED is ON ..................... 22-7
LED indication ................................................ 9-17
Lightning surge absorber ..............................19-19
Link direct device ..............................................4-2
Link register [W] ................................................4-2
Link relay [B] .....................................................4-2
Local device
Data clear of local device...........................12-27
Monitor test of local device (function version B or
later).............................................................8-12
Use of local device (Function version B or later)
.............................................................. App-149
Local pointer..................................................12-17
LOW VOLTAGE DIRECTIVES......................20-11
low-speed END processing ...........................12-14
Low-speed execution type program ................12-9
Low-speed execution monitoring time...........12-15
Low-speed scan time ....................................12-14
Low-speed timer [T] ..........................................4-2
Low-speed timers [T].......................................13-1
[M]
Main Base Unit......................................... App-145
Main base unit for high-speed access (A38HB)
........................................................................17-3
Memory capacity ...............................................4-1
Memory card
Handling Memory Cards ..............................18-3
Installing the batterie to the memory card
.....................................................................18-7
Installing/Removing A Memory Card ...........18-8
Memory card battery specifications .............18-4
Memory Card Specifications........................18-1
Part Names of Memory Card .......................18-6
Microcomputer program ........................... App-124
[(delete)]
Installation..................................................19-12
Removal.....................................................19-14
Monitor
Monitor function .............................................8-2
Monitoring condition setting ...........................8-2
[N]
Network module ................................................1-2
NETWORK RELAY FROM ETHERNET MODULE
(FUNCTION VERSION B OR LATER)..... App-153
Noise filter (power supply line filter) ..............20-10
Notes
DESIGN PRECAUTIONS............................. A-1
DISPOSAL PRECAUTIONS......................... A-6
Handling precautions ...................................16-8

Mitsubishi Q2ACPU Specifications

General

Brand	Mitsubishi
Model	Q2ACPU
Category	Controller
Language	English