Name: Rigol DS1000Z Series
Brand: Rigol
Rating: 4 (1 reviews)

To Next Page

To Previous Page

RIGOL Chapter 3 To Set the Horizontal System

DS1000Z User’s Guide

3-4

Time Base Mode

Press MENU in the horizontal control area (HORIZONTAL) at the front panel and

then press Time Base to select the time base mode of the oscilloscope and the

default is YT.

YT Mode

This mode is the main time base mode and is applicable to two input channels.

In this mode, the Y axis represents voltage and the X axis represents time. Note that

only when this mode is enabled can “

Delayed Sweep” be turned on.

Guaranty and Declaration3
Safety Requirement4
- General Safety Summary4
- Safety Terms and Symbols6
- Measurement Category7
- Ventilation Requirement8
- Working Environment9
  - Pollution Degree10
  - Pollution Degree Definitions10
- General Care and Cleaning11
- Environmental Considerations12
DS1000Z Series Overview13
- Main Features13
Document Overview15
- Table of Contents18
Chapter 1 1 Quick Start25
- General Inspection26
- Appearance and Dimensions27
- To Prepare the Oscilloscope for Use28
- Front Panel Overview35
- Rear Panel Overview36
- Front Panel Function Overview38
- User Interface43
- To Use the Security Lock47
- To Use the Built-In Help System48
Chapter 2 2 to Set the Vertical System49
- To Enable the Channel50
- Channel Coupling51
- Bandwidth Limit51
- Probe Ratio52
- Waveform Invert53
- Vertical Scale53
- Vertical Expansion54
- Amplitude Unit54
- Channel Label55
Chapter 3 3 to Set the Horizontal System57
- Delayed Sweep58
- Time Base Mode60
Chapter 4 4 to Set the Sample System65
- Acquisition Mode66
- Sin(X)/X68
- Sample Rate69
- Memory Depth71
Chapter 5 5 to Trigger the Oscilloscope73
- Trigger Source74
- Trigger Mode75
- Trigger Coupling77
- Trigger Holdoff78
- Noise Rejection79
- Trigger Type80
- Trigger Output Connector113
Chapter 6 6 to Make Measurements115
- Math Operation116
- Auto Measurement132
- Cursor Measurement143
Chapter 7 7 Protocol Decoding151
- Parallel Decoding152
- RS232 Decoding (Option)155
- I2C Decoding (Option)161
- SPI Decoding (Option)165
Chapter 8 8 Reference Waveform169
- To Enable REF Function170
- To Select REF Source170
- To Adjust REF Waveform Display171
- To Save to Internal Memory171
- To Set the Color171
- To Reset the REF Waveform171
- To Export to Internal or External Memory172
- To Import from Internal or External Memory172
Chapter 9 Pass/Fail Test173
- To Enable Pass/Fail Test174
- To Select Source174
- Mask Range174
- Test and Ouput175
- To Save the Test Mask176
- To Load the Test Mask176
Chapter 10 10 Waveform Record177
- Playback Setting178
- Record Setting179
Chapter 11 11 Display Control181
- To Select the Display Type182
- To Set the Persistence Time183
- To Set the Waveform Intensity185
- To Set the Screen Grid185
- To Set the Grid Brightness185
- To Set the Menu Display185
Chapter 12 12 Signal Source187
- To Output Basic Waveform188
- To Output Built-In Waveform193
- To Output Arbitrary Waveform198
- Modulation205
Chapter 13 Store and Recall207
- Storage System208
- Storage Type209
- Internal Storage and Recall211
- External Storage and Recall212
- Disk Management213
- Factory220
Chapter 14 14 System Function Setting229
- Remote Interface Configuration230
- System-Related235
Chapter 15 15 Remote Control239
- Remote Control Via USB240
- Remote Control Via LAN244
Chapter 16 16 Troubleshooting247
Chapter 17 17 Specifications249
- Runt Trigger251
Chapter 18 18 Appendix259
- Appendix A: Accessories and Options259
- Appendix B: Warranty260
- Appendix C: any Question or Comment261
Chapter 19 Index263

Rigol DS1000Z Series User Manual

Table of Contents

Other manuals for Rigol DS1000Z Series

Questions and Answers:

Rigol DS1000Z Series Specifications

Related product manuals

Brand	Rigol
Model	DS1000Z Series
Category	Test Equipment
Language	English