27GB
- ear protection to prevent damage to your ears,
- a breathing mask to avoid the risk of inhaling
hazardous particles of dust,
- safety gloves to avoid injuries from sharp edges
or knives,
- safety goggles to avoid eye injuries from ying
parts.
• It is imperative that the following situations are
avoided at all times: Premature interruption of the
cutting operation (planing cuts which do not com-
plete the entire length of the workpiece; planing of
uneven pieces of wood which do not lie at on the
infeed table).
• Important! If the primary mains connection is in a
poor condition there is a risk of short-circuits when
the machine is switched on. This may also affect
other functions (e.g. the lighting up of indicator
lamps). Should there be any faults in the primary
mains connection, please contact your local elec-
tricity supplier to advice and information.
Residual risks
Even when the machine is used as prescribed it is
still impossible to eliminate certain residual risk fac-
tors. There is a risk of the following injuries in con-
nection with the required operation of the machine:
• m WARNING! Danger of injury!
of ngers and hands by contact with the blade
shaft at uncovered areas when changing tools.
These can also be crushed by opening the guard.
• Eye injuries
• on the infeed and discharge opening by
dangerous recoil
• Danger from current if the electric cables have not
been connected correctly.
• harmful wood duct may be generated if operated
without an extractor or chip bag.
• by catapulted parts
• Metal parts in the workpiece can blunt or destroy
the blades.
• Lung damage if no suitable protective dust mask
is used.
m WARNING! Hearing damage!
A longer stay in the immediate vicinity of the running
unit may cause hearing damage.
Wear ear protectors!
Despite the observance of the operating instructions
there still may be some hidden residual risks.
Warning! This electric tool generates an electro-
magnetic eld during operation. This eld can impair
active or passive medical implants under certain
conditions. In order to prevent the risk of serious or
deadly injuries, we recommend that persons with
medical implants consult with their physician and the
manufacturer of the medical implant prior to operat-
ing the electric tool.
Emergency procedure
Conduct a rst-aid procedure adequate to the
injury and summon qualied medical attendance as
quickly as possible. Protect the injured person from
further harm and calm them down.
For the sake of eventual accident, in accordance
with DIN 13164, a workplace has to be tted with a
rst-aid kit. It is essential to replace any used mate-
rial in the rst-aid kit immediately after it has been
used. If you seek help, state the following pieces of
information:
1. Accident site
2. Accident type
3. Number of injured persons
4. Injury type(s)
6. Technical data
Technical data
Number of knives
2 pieces
Cutter block rpm
8500 1/min
Dimensions
970 x 490 x 485 mm
Weight
30 kg
Technical data – Surfacing
Max planing width
254 mm
Max chip removal
2 mm
Ripping fence l x h
635 x 127 mm
Ripping fence tilting
angle
90°–135°
Surfacing table size
920 x 264 mm
Technical data – Thicknessing
Max planing width
254 mm
Max planing
thickness
120 mm
Max chip removal
2 mm
Thicknessing table
size
380 x 254 mm
Drive
Motor V/Hz
230V / 60 Hz
Consumption power
P1
1500 W
Subject to technical changes!
Sound
Sound values were measured in accordance with
EN 61029.
Sound pressure level L
pA
89 dB(A)
Uncertainty K
pA
3 dB
Sound power level L
WA
102 dB(A)
Uncertainty K
WA
3 dB
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Keep the noise emissions and vibrations to a
minimum!
• Only use appliances which are in perfect working
order.
• Service and clean the appliance regularly.
• Adapt your working style to suit the appliance.
• Do not overload the appliance.
• Have the appliance serviced whenever necessary.
• Switch the appliance off when it is not in use.
To Next Page
Loading...
Need help?
General
Weight and Dimensions
