14/lIGHTING
SYSTEM,
INSTRUMENTS
100
Settina:
the
clock
D
~
\I~
- C
ct
18:
I?:"I1
"-----
___
---'--1,1
\
ClJ(
Condition
The motorcycle is stationary.
-
Press
the button
'Q
briefly and repeatedly until Cll( appears at the bottom right of
the display.
-
Press
the button
'Q
for 3 - 5 seconds.
,/
The hour display flashes.
- Set the hour display with the button
andlor button .
-
Press
the button Q briefly.
,/
The next segment of the display flashes and can be set.
-
You
can set the following segments in the same
way
as
the hours by pressing the
'-
__________
4;":O,;:,03:..:3,;:,D-O,;;,,:,,,JI
button and the button
~
.
Checkina:
the
haadlia:ht
adjustment
•
•
400726-10
Adjustina:
the
headlia:ht
ran~
--------------------------------------
•
Info
I The seconds can only
be
set
to
zero.
-
Press
the button 0 for 3 - 5 seconds.
,/
The settings are stored and the Setup menu is closed.
•
Info
I
If
no
button
is
pressed for 20 seconds, or
if
a pulse arrives from the wheel
speed sensor, the settings are stored automatically and the Setup menu is
closed.
- Stand the vehicle upright
on
a horizontal surface in front of a light wall and make a
mark at the height
of
the center of the low beam headl ight.
- Make another mark
at
a
distance.
under the first mark.
Guideline
1
Distance.
15
cm
(2
in)
- Position the vehicle vertically at a
distance.
in front of the wall.
Guideline
1
Distance.
15m
(16
tt)
- The rider now sits down
on
the motorcycle.
- Switch
on
the low beam.
- Check the headlight adjustment.
The border between light and dark must
be
exactly at the lower mark when the
motorcycle
is
operational and complete with rider.
•
If
the boundary between light and dark does not meet specifications:
- Adjust the headlight range.
(r
p.
100)
- Check the headlight adjustment. (r
p.
100)
- Loosen screw
O.
- Adjust the headlight range of the headlight
by
moving
it
up or down.
Guideline
The boundary between light and dark must be exactly on the lower mark for a
motorcycle with a rider (mark
is
applied under: Checking the headlight setting).
•
Info
I A change in weight
on
the vehicle may require a correction of the headlight
range.
- Tighten screw
•.
14/lIGHTING
SYSTEM,
INSTRUMENTS
100
Settina:
the
clock
D
~
\I~
- C
ct
18:
I?:"I1
"-----
___
---'--1,1
\
ClJ(
Condition
The motorcycle is stationary.
-
Press
the button
'Q
briefly and repeatedly until Cll( appears at the bottom right of
the display.
-
Press
the button
'Q
for 3 - 5 seconds.
,/
The hour display flashes.
- Set the hour display with the button
andlor button .
-
Press
the button Q briefly.
,/
The next segment of the display flashes and can be set.
-
You
can set the following segments in the same
way
as
the hours by pressing the
'-
__________
4;":O,;:,03:..:3,;:,D-O,;;,,:,,,JI
button and the button
~
.
Checkina:
the
haadlia:ht
adjustment
•
•
400726-10
Adjustina:
the
headlia:ht
ran~
--------------------------------------
•
Info
I The seconds can only
be
set
to
zero.
-
Press
the button 0 for 3 - 5 seconds.
,/
The settings are stored and the Setup menu is closed.
•
Info
I
If
no
button
is
pressed for 20 seconds, or
if
a pulse arrives from the wheel
speed sensor, the settings are stored automatically and the Setup menu is
closed.
- Stand the vehicle upright
on
a horizontal surface in front of a light wall and make a
mark at the height
of
the center of the low beam headl ight.
- Make another mark
at
a
distance.
under the first mark.
Guideline
1
Distance.
15
cm
(2
in)
- Position the vehicle vertically at a
distance.
in front of the wall.
Guideline
1
Distance.
15m
(16
tt)
- The rider now sits down
on
the motorcycle.
- Switch
on
the low beam.
- Check the headlight adjustment.
The border between light and dark must
be
exactly at the lower mark when the
motorcycle
is
operational and complete with rider.
•
If
the boundary between light and dark does not meet specifications:
- Adjust the headlight range.
(r
p.
100)
- Check the headlight adjustment. (r
p.
100)
- Loosen screw
O.
- Adjust the headlight range of the headlight
by
moving
it
up or down.
Guideline
The boundary between light and dark must be exactly on the lower mark for a
motorcycle with a rider (mark
is
applied under: Checking the headlight setting).
•
Info
I A change in weight
on
the vehicle may require a correction of the headlight
range.
- Tighten screw
•.
To Next Page
Loading...
Need help?
General
