301ENGINE
ASSEMBLY
Installlnilhe
klckstaner
151
- Put the water pump cover seal in place.
- Put the water pump cover on. Mount
screw.
with the
seal
washer and tighten
it
after all screws of the water pump cover
have
been
mounted.
Guideline
1 Screw, water pump cover
1 M6x25
110
Nm
(7.4
Ibf
ft) 1
- Mount
screws.
and tighten once all of the water pump cover screws
have
been
mounted.
Guideline
1 Screw, water pump cover 1 M6x25
110
Nm
(7.4
Ibf
It)
1
- Mount
screw.
and tighten all screws in a crisscross pattern.
Guideline
I
Screw,
water
pump
cover
1 M6x55
- Position the kickslarter. Mount and tighten screw
O.
Guideline
Screw, kickstarter M8
25
Nm
(18.4
Ibf
It)
- Oil the internal rotor and external rotor before mounting.
1 Engine oil (SAE lOW/50) (
..
p.
250)
- Insert O-ri ng
•.
110
Nm
(7.4
Ibf
It)
1
Loctile-
243""
- Position
pin.
in oil pump
shaft.
and slide
on
the internal rotor.
_
Info
I
Marking.
of
the internal rotor faces outward.
- Mount the external
rotor.
with the marking facing inward.
_
Info
I The marking should not
be
visible after installation.
- Check that the pin of the suction pump
is
seated properly.
- Position oil pump cover
•.
Mount and tighten screws
•.
Guideline
Screw,
oil
pump
cover
M5
6Nm
Loctile-
222
(4.4
Ibf
It)
301ENGINE
ASSEMBLY
Installlnilhe
klckstaner
151
- Put the water pump cover seal in place.
- Put the water pump cover on. Mount
screw.
with the
seal
washer and tighten
it
after all screws of the water pump cover
have
been
mounted.
Guideline
1 Screw, water pump cover
1 M6x25
110
Nm
(7.4
Ibf
ft) 1
- Mount
screws.
and tighten once all of the water pump cover screws
have
been
mounted.
Guideline
1 Screw, water pump cover 1 M6x25
110
Nm
(7.4
Ibf
It)
1
- Mount
screw.
and tighten all screws in a crisscross pattern.
Guideline
I
Screw,
water
pump
cover
1 M6x55
- Position the kickslarter. Mount and tighten screw
O.
Guideline
Screw, kickstarter M8
25
Nm
(18.4
Ibf
It)
- Oil the internal rotor and external rotor before mounting.
1 Engine oil (SAE lOW/50) (
..
p.
250)
- Insert O-ri ng
•.
110
Nm
(7.4
Ibf
It)
1
Loctile-
243""
- Position
pin.
in oil pump
shaft.
and slide
on
the internal rotor.
_
Info
I
Marking.
of
the internal rotor faces outward.
- Mount the external
rotor.
with the marking facing inward.
_
Info
I The marking should not
be
visible after installation.
- Check that the pin of the suction pump
is
seated properly.
- Position oil pump cover
•.
Mount and tighten screws
•.
Guideline
Screw,
oil
pump
cover
M5
6Nm
Loctile-
222
(4.4
Ibf
It)
To Next Page
Loading...
Need help?
General
