Dell PowerConnect 3548 User Manual

282 Configuring Switch Information
Configuring IP Based ACLs with CLI Commands
The following table summarizes the equivalent CLI commands for configuring IP Based ACLs.
Table 7-5. IP Based ACL CLI Commands
CLI Command Description
ip access-list access-list-name
no ip access-list access-list-name
To define an IPv4 access list and to
place the device in IPv4 access list
configuration mode, use the ipv4
access-list command in global
configuration mode. To remove the
access list, use the no form of this
command.
permit {any| protocol} {any|{source source-wildcard}}
{any|{destination destination-wildcard}} [dscp number | ip-precedence
number] [fragments]
permit-icmp {any|{source source-wildcard}} {any|{destination
destination-wildcard}} {any|icmp-type} {any|icmp-code} [dscp number |
ip-precedence number]
permit-igmp {any|{source source-wildcard}} {any|{destination
destination-wildcard}} {any|igmp-type} [dscp number | ip-precedence
number]
permit-tcp {any|{ source source-wildcard}} {any|source-port} {any|{
destination destination-wildcard}} {any|destination-port} [dscp number |
ip-precedence number] [flags list-of-flags]
permit-udp {any|{ source source-wildcard}} {any| source-port}
{any|{destination destination-wildcard}} {any|destination-port} [dscp
number | ip-precedence number]
To set conditions to allow a packet to
pass a named IP access list, use the
permit command in access list
configuration mode.
deny [disable-port] {any| protocol} {any|{source source-wildcard}}
{any|{destination destination-wildcard}} [dscp number | ip-precedence
number] [fragments]
deny-icmp [disable-port] {any|{source source-wildcard}}
{any|{destination destination-wildcard}} {any|icmp-type} {any|icmp-
code} [dscp number | ip-precedence number]
deny-igmp [disable-port] {any|{source source-wildcard}}
{any|{destination destination-wildcard}} {any|igmp-type} [dscp number
| ip-precedence number]
deny-tcp [disable-port] {any|{ source source-wildcard}} {any|source-
port} {any|{ destination destination-wildcard}} {any|destination-port}
[dscp number | ip-precedence number] [flags list-of-flags]
deny-udp [disable-port] {any|{ source source-wildcard}} {any| source-
port} {any|{destination destination-wildcard}} {any|destination-port}
[dscp number | ip-precedence number]
To set conditions to allow a packet to
pass a named IP access list, use the
deny command in access list
configuration mode.

Dell PowerConnect 3548 Specifications

General

MAC address table	8000 entries
Maximum data transfer rate	0.1 Gbit/s
Supported data transfer rates	10/100 Mbps
10G support	-
Number of VLANs	256
Flow control support	Yes
Networking standards	IEEE 802.1D, IEEE 802.1p, IEEE 802.1Q, IEEE 802.1s, IEEE 802.1w, IEEE 802.3ad
Dimensions (WxDxH)	440 x 257 x 43.2 mm
Networking features	Gigabit Ethernet, Fast Ethernet
Authentication method	RADIUS, TACACS+
Connectivity technology	Wired
Switch type	Managed
Switch layer	L2
Data link protocols	Ethernet
Supported network protocols	HTTP, HTTPS/SSL, SSH
Power connector	DC-in jack
SFP/SFP+ slots quantity	2
Basic switching RJ-45 Ethernet ports quantity	48
Product color	Black
Storage temperature (T-T)	-20 - 70 °C
Operating temperature (T-T)	0 - 45 °C
Storage relative humidity (H-H)	10 - 95 %
Operating relative humidity (H-H)	10 - 90 %

Weight and Dimensions

Weight	8000 g