DigiTech GNX4 User Manual

Flanger
A Flanger uses the same principle as a Chorus but has a shorter delay time and adds regeneration (or
repeats) to the modulating delay. This results in an exaggerated up and down sweeping motion to the
effect.
Parameter 1 - Knob 2 adjusts the rate (
Speed) of the modulation.Ranges from 0 to 99.
Parameter 2 - Knob 3 adjusts the intensity (
Depth) of the Modulation.Ranges from 0 to 99.
Parameter 3 - Knob 4 adjusts the amount of feedback (
Regen) added to the Flanger delay.Ranges
from 0 to 99.
Mod Mix - Knob 5 controls the mix (
mod mix) of wet and dry signal. Ranges from 0 (all dry) to 99
(all wet).
Phaser
A Phaser splits the incoming signal,takes the split signal in and out of phase and mixes it back in with
the original signal. As the phasing changes,different frequencies are canceled resulting in a warm sort
of twisting sound.
Parameter 1 - Knob 2 adjusts the rate (
Speed) of the modulating phase. Ranges from 0 to 99.
Parameter 2 - Knob 3 adjusts the intensity (
Depth) of the modulation. Ranges from 0 to 99.
Parameter 3 - Knob 4 adjusts the amount of effected signal returned to the input of the Phaser
(
Regen). Ranges from 0 to 99.
*Parameter 4 - Selects the waveform used by the Phaser. Waveforms include: Triangle , Sine,and
Square.
*Parameter 5 - Adjusts the left to right balance of the wet signal. Ranges from L 99
to R 99.
Mod Level - Knob 5 controls the level (
mod levl) of wet and dry signal. Ranges from 0 (all dry)
to
99 (all wet).
Triggered Flanger
A Triggered Flanger is the same sound as a regular Flanger but it lets you choose the starting point of
the Flanger sweep. With a regular Flanger, the low frequency oscillator (LFO) is continually sweeping
up and down. Therefore,when you begin to play, the flanger may be at the top,bottom, or any
random point of the sweep. With a Triggered Flanger,every time the signal exceeds the Sensitivity
level setting, the Flanger begins at the LFO Start Parameter.
Parameter 1 - Knob 2 adjusts the rate (
Speed) of the modulation. Ranges from 0 to 99.
Parameter 2 - Knob 3 adjusts the strength the signal must be (
senstvty) in order to trigger the
Flanger. Ranges from
0 (strong signals) to 99 (weak signals).
Parameter 3 - Knob 4 selects the Flanger sweep starting point (
LFO STrt). Ranges from 0
(bottom of the sweep point) to 99 (top of the sweep point).
Mod Mix - Knob 5 controls the mix (
mod mix) of wet and dry signal. Ranges from 0 (all dry) to
99 (all wet).
Triggered Phaser
A Triggered Phaser is the same sound as a regular Phaser but it lets you choose the starting point of
the Phaser sweep. In a regular Phaser, the low frequency oscillator (LFO) is continually changing the
phase of the signal. Therefore, when you begin to play,the phaser may be at any random point of the
phase. With a Triggered Phaser, every time the signal exceeds the Sensitivity level setting,the Phaser
begins at the LFO Start Parameter.
Parameter 1 - Knob 2 adjusts the rate (
Speed) of the modulating phase. Ranges from 0 to 99.
Parameter 2 - Knob 3 adjusts the strength the signal must be (
senstvty) in order to trigger the
Phaser.Ranges from
0 (strong signals) to 99 (weak signals).
*These Parameters are only available using the X-E
DIT
™
Editor/Librarian software.
40
Effects and Parameters

DigiTech GNX4 Specifications

General

Brand	DigiTech
Model	GNX4
Category	Music Pedal
Language	English