Detune
A Detuner makes a copy of your incoming signal, takes the copied signal slightly out of tune from the
original,and mixes the two signals together. The result is a doubling type of effect as if two guitars
were playing the same part together.
Parameter 1 - Knob 2 selects the Amount (
AMouNT) of detuning applied to the copied pitch in
cents (100 cents equals 1 semitone). Ranges are from 24 cents below (-24) to 24
cents above (24).
Parameter 2 - Knob 3 adjusts the left/right balance of the detuned signal. Ranges from left 99 (
mod
left
99) to right 99 (mod rght 99).
Knob 4 has no function when Detune is selected.
Mod Level - Knob 5 controls the level (
mod levl) of the detuned note. Ranges from 0 to 99.
Pitch Shift
A Pitch Shifter copies the incoming signal,then shifts the pitch of the copied note to a different note.
The shifted note is then mixed back with the original signal sounding as if two guitars were playing
parallel notes.
Parameter 1 - Knob 2 adjusts the Amount of Pitch Shift (
SHIFT) in intervals of one semi-tone.
Ranges from 12 semitones (-12) below to 24 semitones (24) above.
Parameter 2 - Knob 3 adjusts the left/right balance of the shifted pitch. Ranges from left 99 (
mod
left
99) to right 99 (mod rght 99).
Knob 4 has no function when Pitch Shift is selected.
Mod Level - Knob 5 controls the level (
mod levl) of the shifted pitch. Ranges from 0 to 99.
Delay
Delay records a portion of the incoming signal, and plays it back a short time later. The recorded segment
can repeat just once,several times, or infinitely (that turns off the input to the Delay and lets you play
over the top of a passage in the Delay loop). The Delay in the GNX4 also includes a Ducker Threshold
that lets you set the signal strength required before the Delay records. This feature lets you control the
Delay with your playing.
Delay On/Off -The Status button turns the Delay (
delay) on and off.
Delay Type - Knob 1 selects one of the 5 different types of Delay. The Delay choices include:
Time - Knob 2 adjusts the length of time between repeats. Ranges from 0 through 2000 milliseconds (
0
MS through 2000 MS
) in 1 ms increments. Use the DATA WHEEL while the Delay Time
appears in the Display to adjust the Delay Time in 100 ms increments.
Feedback - Knob 3 adjusts the number of times the delayed signal will repeat (
feedback). Ranges
from
0 to 99 and rpt hold (infinite repeat).
Ducker Threshold - Knob 4 adjusts the level (
threshld) the input signal must reach before the Delay
signal is attenuated. Ranges from
1 to 99 and off (oF).
*Ducker Attenuation -The Ducker Level selects the amount of attenuation applied to the Delay signal
when the Ducker Threshold has been exceeded.Ranges from 0 to 99.
*Delay Balance -The Delay Balance adjusts the left/right balance of the Delay signal.Ranges from L 99
to R 99.
Spread -This parameter increases or decreases the stereo imaging for the Spread Delay. Range is 1-50.
Delay Level - Knob 5 adjusts the volume (
dly levl) of the Delay signal. Ranges from 0 to 99.
*These Parameters are only available using the X-E
DIT
™
Editor/Librarian software.
MONO (clear concise repeats)
pingpong (bounces from side to side)
ANALOG (deteriorates with each repeat)
anlgpong (side to side with deterioration)
Spread (clear concise repeats with stereo
imaging)
43
Effects and Parameters
To Next Page
Loading...
Need help?
General
