To Next Page

To Previous Page

GE HEALTHCARE

IRECTION 5305880-100, REVISION 3 LOGIQ™ 100 PRO SERVICE MANUAL

Page 10-4 Section 10-3 - Periodic Maintenance Schedule

Section 10-4 Tools Required

10-4-1 Standard GE Tool Kit

The following is a description of the “Standard” GE tool kit in the USA. Not all tools are required for PMs.

Tool ID Description Tool ID Description

9-45358 Pliers Retaining Ring 9-XL9971MM Xcelite-hex Blade 1.27mm

9-4078 Scribe 9-XL9972MM Xcelite-hex Blade 1.5mm

9-44572 Wrench Open End 3/8 - 7/16 9-XL9973MM Xcelite-hex Blade 2 mm

9-44579 Wrench Open End 1/2 - 9/16 9-XL9974MM Xcelite-hex Blade 2.5mm

9-44579 Wrench Open End 1/2 - 9/16 9-XL9975MM Xcelite-hex Blade 3mm

9-45385 Pliers, Arc Joint 7 inch 9-XL9976MM Xcelite-hex Blade 4mm

9-45378 Pliers, Slip Joint 9-XL9977MM Xcelite-hex Blade 5mm

9-4518 Pliers, Long Nose, Miniature 9-XL991CM Handle

9-4518 Pliers, Long Nose, Miniature C2356E Screw starter - Kedman Quick Wedge

9-44776 Ignition Wrench Set, 10 pc. BLBO Box - 18 Compartment

9-44601 Wrench, Adj., 4 inch DWL4283T Box - 5 Compartment

9-4151 Screwdriver, Blade, Stubby 9-41322 Pickup Tool, Claw type

9-41421 Screwdriver, Blade, Pocket clip 9-6757 6 pc Needle File Set

9-41594 Screwdriver, Blade 1/8 in. x 4 in. 9-9487 Utility Knife

9-41581 Screwdriver, Blade 3/16 in. x 4 in. 9-45341 Pliers Vice Grip 10 inch

9-39451 20' Steel Tape, locking Spring load 9-3001 Xacto Pen Knife

9-GH807 Ratchet, Offset, Slotted 9-HT62002 Solder Aid, Fork and Hook

68-412 Ratchet, Offset, Phillips 9-4099 Mirror, Round, Telescoping

9-GH130 Tapered Reamer 9-GH3001 Steel Rule Decimal 6 inch

9-41584 Screwdriver, slotted 1/4 in.X 6 in. 9-GH300ME Steel Rule Metric 6 inch

9-4118 Screwdriver, Phillips #2, Stubby 9-XL9920 Xcelite-hex Blade.050 inch

9-41293 Screwdriver, Phillips #0 9-XL9921 Xcelite-hex Blade 1/16 inch

9-41294 Screwdriver, Phillips #1 9-XL9922 Xcelite-hex Blade 5/16 inch

9-41295 Screwdriver, Phillips #2 9-XL9923 Xcelite-hex Blade 3/32 inch

9-46677 Hex Keys, 20 pc., Metric 9-XL9924 Xcelite-hex Blade 1/8 inch

9-34701 1/4 in. Standard.Socket set (19 pc) 9-XL9925 Xcelite-hex Blade 5/32 inch

9-43499 1/2 inch Socket 1/4 inch drive 9-XL9926 Xcelite-hex Blade 3/16 inch

Table 10-3 Overview of GE-1 Tool Kit Contents

State: RELEASE - Document is released and under formal Change Control. Changes are subject to the ECR/ECO Process.

See the GEHC Myworkshop System to determine the status of this document.

Approved Document - 5305880-100TPH_r3.pdf Page 175 of 197

GE LOGIQ 100 PRO User Manual

Questions and Answers: