EasyManuals Logo
Home>Xerox>Printer>Phaser 4600

Xerox Phaser 4600 Service Manual

Xerox Phaser 4600
409 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #358 background imageLoading...
Page #358 background image
04/2016
6-26
Phaser 4600/4620/4622 Printer Service Manual
dC131
Revised
6 General Procedures and Information
dC131 NVM Read/Write
Purpose
To review and modify values within the machine configuration and control parameters stored in
NVM.
Description
Each NVM item is identified using a chain and location code in the form XX-XXX, where XX- is
the chain prefix, and -XXX is an identifier in the range 001 to 999. For example 05-100.
NOTE: Tray numbering is dynamic according to available configuration, such that the registra-
tion adjustments must be accomplished by adjusting the appropriate tray listed in the configu-
ration. For example, if the configuration is 5 trays and the 5th tray is the HCF, use Tray 5
registration adjustments for the HCF.
Procedure
1. Enter diagnostics, GP 1.
2. Select Diagnostic Routines.
3. Select the required dC routine category:
4. Select 131 NVM Read/Write.
5. Select the appropriate NVM chain.
6. View or edit the chain as necessary.
7. Refer to the tables that follow for NVM chain locations and parameters:
• Table 1 NVM chain 7
• Table 2 NVM chain 8
• Table 3 NVM chain 9
• Table 4 NVM chain 10
8. When the values of an editable NVM have been changed, switch off the machine, the
switch on the machine, to check and evaluate the changes made to the NVM.
Table 1 NVM Chain 7
Location NVM Name NVM Description Value Default
07-100 Top Registration
Tray 1 Simplex
The changed dimension of Tray
1 top registration in simplex
0 ~ 60 (0.5mm / 13
steps)
30
07-110 Side Registration
Tray 1 Simplex
The changed dimension of Tray
1 side registration in simplex.
0 ~ 60 (0.5mm / 13
steps)
30
07-120 Top Registration
Tray 1 Dup_long
(2nd side)
1 top registration of 2nd side in
duplex long.
0 ~ 60 (0.5mm / 13
steps)
30
07-130 Side Registration
Tray 1 Dup_long
(2nd side)
The changed dimension of tray
1 side registration of 2nd side
in duplex long
0 ~ 60 (0.5mm / 13
steps)
30
07-140 Top Registration
Tray 1 Duplex
(1st side)
The changed dimension of tray
1 top registration of 1st side in
duplex long and short.
0 ~ 60 (0.5mm / 13
steps)
30
07-150 Side Registration
Tray 1 Duplex
(1st side)
The changed dimension of tray
1 side registration of 1st side in
duplex long and short.
0 ~ 60 (0.5mm / 13
steps)
30
07-200 Top Registration
Tray 2 Simplex
The changed dimension of Tray
2 top registration in simplex
0 ~ 60 (0.5mm / 13
steps)
30
07-210 Side Registration
Tray 2 Simplex
The changed dimension of Tray
2 side registration in simplex.
0 ~ 60 (0.5mm / 13
steps)
30
07-220 Top Registration
Tray 2 Dup_long
(2nd side)
1 top registration of 2nd side in
duplex long.
0 ~ 60 (0.5mm / 13
steps)
30
07-230 Side Registration
Tray 2 Dup_long
(2nd side)
The changed dimension of Tray
2 side registration of 2nd side
in duplex long
0 ~ 60 (0.5mm / 13
steps)
30
07-240 Side Registration
Tray 2 Duplex
(1st side)
The changed dimension of Tray
2 top registration of 1st side in
duplex long and short.
0 ~ 60 (0.5mm / 13
steps)
30
07-250 Top Registration
Tray 3 Simplex
The changed dimension of Tray
2 side registration of 1st side in
duplex long and short.
0 ~ 60 (0.5mm / 13
steps)
30
07-300 Top Registration
Tray 3 Simplex
The changed dimension of Tray
3 top registration in simplex
0 ~ 60 (0.5mm / 13
steps)
30
07-310 Side Registration
Tray 3 Simplex
The changed dimension of Tray
3 side registration in simplex.
0 ~ 60 (0.5mm / 13
steps)
30
07-320 Top Registration
Tray 3 Dup_long
(2nd side)
1 top registration of 2nd side in
duplex long.
0 ~ 60 (0.5mm / 13
steps)
30
07-330 Side Registration
Tray 3 Dup_long
(2nd side)
The changed dimension of Tray
3 side registration of 2nd side
in duplex long
0 ~ 60 (0.5mm / 13
steps)
30
07-340 Side Registra-
tion Tray 3
Duplex (1st side)
The changed dimension of Tray
3 top registration of 1st side in
duplex long and short.
0 ~ 60 (0.5mm / 13
steps)
30
07-350 Top Registration
Tray 3 Duplex
(1st side)
The changed dimension of Tray
3 side registration of 1st side in
duplex long and short.
0 ~ 60 (0.5mm / 13
steps)
30
07-400 Top Registration
Tray 4 Simplex
T
he changed dimens
ion of Tray
4 top registration in simplex
0 ~ 60 (0.5mm / 13
steps)
30
07-410 Side Registration
Tray 4 Simplex
The changed dimension of Tray
4 side registration in simplex.
0 ~ 60 (0.5mm / 13
steps)
30
07-420 Top Registration
Tray 4 Dup_long
(2nd side)
1 top registration of 2nd side in
duplex long.
0 ~ 60 (0.5mm / 13
steps)
30
07-430 Side Registration
Tray 4 Dup_long
(2nd side)
The changed dimension of Tray
4 side registration of 2nd side
in duplex long
0 ~ 60 (0.5mm / 13
steps)
30
Table 1 NVM Chain 7
Location NVM Name NVM Description Value Default

Table of Contents

Other manuals for Xerox Phaser 4600

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Xerox Phaser 4600 and is the answer not in the manual?

Xerox Phaser 4600 Specifications

General IconGeneral
BrandXerox
ModelPhaser 4600
CategoryPrinter
LanguageEnglish

Related product manuals