59
Display Explanation Action/Explanation
Now Playing! This operation cannot be executed because playback is occurring. Stop playback, and then execute.
CLIP NOT EXIST!
The clip that is the target of the operation does not exist.
This appears if an empty clip is selected as the target of a copy or edit
operation.
Make sure that the target clip is correctly selected.
EMPTY CLIP The clip that is the target of the operation does not exist.
EMPTY TRACK
The track that is the target of the operation does not exist.
This appears if an empty track is selected as the target of a copy or edit
operation.
Make sure that the target track is correctly selected.
CLIP NOT EMPTY
The clip slot that is the target of the operation is already in use.
It is possible to simultaneously select the same clip number of all tracks (p.
14) and perform copy and paste, but the paste-destination clip slots must
all be empty.
Either select an empty clip slot, or delete clips before executing.
For new loop, delete the existing
clip!
When loading a looper clip, this message appears if you attempt to
overwrite an existing clip.
Looper clips cannot be imported by overwriting an existing clip.
TRACK NOT EMPTY The track paste-destination is not empty. Either select an empty track, or delete the applicable track before executing.
WRONG TRACK TYPE
The copy-source and copy-destination track types are dierent.
You can’t copy clips between tracks of dierent types.
Copy the clip to a track type that is the same as the copy-source.
PLEASE SELECT TRACK
A track is selected for copying, but a track is not selected as the paste-
destination.
Select a track and then paste.
PLEASE SELECT LINE
The clip line is selected for copying, but a clip line is not selected as the
paste-destination.
Select a clip line and then paste.
PLEASE SELECT CLIP
A clip is selected for copying, but a clip is not selected as the paste-
destination.
Select a clip and then paste.
ALREADY USED!
The specied track type is already used.
This appears if a drum track with compressors is already in use, and you
attempt to create a new drum track with compressors.
Either delete the existing drum track with compressors, or use a
conventional drum track.
File Write Error! Failed to save the project le.
For some reason, the le could not be saved.
You might be able to solve this problem by formatting the SD card.
Before formatting the SD card, make a backup by saving any important les
to your computer.
Can’t Write
This le name is locked.
Writing is not possible because the le is locked.
You can’t save using the same name as a locked project.
As described in “Managing Projects” (p. 17), unlock the le and then
overwrite it, or save the le with a dierent name.
Abort. **** is locked le. The le could not be deleted because it is locked.
A locked project cannot be deleted.
If you want to delete the project, unlock it.
Now Playing. Please Stop the
Sequencer.
This operation cannot be executed because playback is in progress. Stop playback and then execute the operation.
Abort! File can’t open The wave le could not be opened. The le or SD card that you attempted to load might be damaged.
Abort! File format error The sample le format is not supported by the MC-707.
The MC-707 supports 32–96 kHz, 16-bit and 24-bit (mono/stereo) Wav
format les.
Use your computer to convert the le format, and try the operation again.
Abort! File read error The le could not be read for some reason.
If the Wav le format you are attempting to read is not common, there
might be cases when the le cannot be read.
Abort! Memory full
The le could not be imported because there is insucient internal memory
in the MC-707.
Use the Sample Bank browser (p. 19) to delete unneeded user samples.
Abort! Not enough contiguous
memory
Unable to allocate enough contiguous memory for importing.
It might be that the internal memory has been fragmented. Execute
“Optimizing the Internal Memory (LOOPER OPTIMIZE)” (p. 55).
If the same error occurs even after optimizing, delete unneeded looper clips
from the project.
Abort! Exceed the Max samples
count
Import was not possible because it would exceed the maximum number of
user samples.
The MC-707 can handle a maximum of 500 user samples.
Use the Sample Bank browser (p. 19) to delete unneeded user samples.
Abort! Too short samples The le could not be imported because the sample is too short.
The length of samples that can be handled by a looper clip is from one
second to 60 seconds.
Use your computer to edit the Wav le to this length, and execute the
operation again.
* Depending on the tempo setting, there are cases in which an even shorter or
longer sample can be handled.
Abort! Too long samples The le could not be imported because the sample is too long.
Format SD CARD Error! Failed to format the SD card.
Turn o the power, rmly insert the SD card, and then turn the power on
again.
NO SD CARD
The SD card is not inserted.
Alternatively, it is incompletely inserted.
SD CARD PROTECTED The SD card is set to a write-protect state.
Remove the SD card, and change the position of the lock switch on its left
side.
TOO MANY LOOPER TRACKS!
The operation could not be executed because the maximum number of
looper tracks that can be created has been reached.
Delete unneeded looper tracks, and execute the operation again.
WAVE1 SAMPLE OFF
The sample cannot be edited because a user sample is not assigned to
WAVE1 of the instrument being edited.
Make sure that a sample is assigned to the instrument that you’re editing,
and execute the operation again.
WAVE1 NOT USER SAMPLE
The sample cannot be edited because a user sample is not specied for
WAVE1 of the instrument being edited.
Make sure that a sample is assigned to the instrument that you’re editing,
and execute the operation again.
Memory Full!
The operation could not be executed because there is insucient looper
memory.
Delete unneeded looper clips, and execute the operation again.
Error Message List
To Next Page
Loading...
Need help?
General
Weight and Dimensions
