282
Intel
®
855GME Chipset and Intel
®
6300ESB ICH Embedded Platform Design Guide
Schematic Checklist Summary
Table 131. GMCH Decoupling Recommendations Checklist (Sheet 1 of 2)
Pin Name Configuration F Qty Notes
√
VCC[18:1]
Connect to
V1P35_GMCH.
0.1 µF
150 µF
10 µF
4
2
1
Bulk decoupling is based on VR
solutions used on CRB design.
VTTLF[21:1] Connect to VCCP
0.1 µF
270 µF
10 µF
3
1
1
Bulk decoupling is based on VR
solutions used on CRB design.
VTTHF[5:1] 0.1 µF 5
Connect pins directly to caps to
GND.
VCCHL[8:1]
Connect to
V1P35_GMCH.
0.1 µF
10 µF
2
1
Bulk decoupling is based on VR
solutions used on CRB design.
VCC_SM[37:1]
Connect to
V_2P5_SM.
0.1 µF
150 µF
11
2
Bulk decoupling is based on VR
solutions used on CRB design.
VCC_QSM[2:1]
Connect to
V_2P5_SM with filter
network.
0.1 µF
4.7 µF+1
Ω
1
1 each
0.68 µH from power supply to
GMCH pins. On GMCH side of
inductor: one 0.1 µF to GND,
4.7 µF + 1
Ω to GND.
VCCASM[2:1]
Connect to
V1P35_GMCH with
filter network.
0.1 µF
100 µF
1
1
1 µH from power supply to GMCH
pins, with caps on GMCH side of
inductor.
VCC_DVO[16:1]
Connect to
V_1P5_CORE.
0.1 µF
10 µF
150 µF
2
1
1
Bulk decoupling is based on VR
solutions used on CRB design.
VCC_ADAC[2:1]
Connect to
V_1P5_CORE.
0.01 µF
0.1 µF
220 µF
(no stuff)
1
1
1
Route VSSADAC to other side of
the caps, then to ground.
Consider a 0-ohm 0805 resistor
between the caps and
V_1P5_CORE.
This and the 220 µF cap footprint
are there in case there is noise
issue with the VGA supply.
VCC_ALVDS
Connect to
V_1P5_CORE
0.1 µF
0.01 µF
1
1
Route VSSALVDS to other side of
the caps, then to ground.
VCC_DLVDS[4:1]
Connect to
V_1P5_CORE
0.1 µF
22 µF
47 µF
1
1
1
Bulk decoupling is based on VR
solutions used on CRB design.
VCC_TXLVDS[4:1]
Connect to
V_2P5_CORE
0.1 µF
22 µf
47 µF
3
1
1
Bulk decoupling is based on VR
solutions used on CRB design.
VCC_GPIO[2:1] Connect to VCC3
0.1 µF
10 µF
1
1
Bulk decoupling is based on VR
solutions used on CRB design.
VCC_AHPLL
Connect to
V1P35_GMCH
0.1 µF 1
NOTE: Decoupling guidelines are recommendations based on our reference board design. Customers may
need to take layout and PCB board design into consideration when deciding on overall decoupling
solution.