Cisco WS-C3560E-24PD-E User Manual

2-457
Catalyst 3560 Switch Command Reference
78-16405-05
Chapter 2 Catalyst 3560 Switch Cisco IOS Commands
show mac access-group
show mac access-group
Use the show mac access-group user EXEC command to display the MAC access control lists (ACLs)
configured for an interface or a switch.
show mac access-group [interface interface-id] [ | {begin | exclude | include} expression]
Syntax Description
Command Modes User EXEC
Command History
Usage Guidelines Expressions are case sensitive. For example, if you enter | exclude output, the lines that contain output
do not appear, but the lines that contain Output appear.
Examples This is an example of output from the show mac-access group user EXEC command. In this display,
port 2 has the MAC access list macl_e1 applied; no MAC ACLs are applied to other interfaces.
Switch> show mac access-group
Interface GigabitEthernet0/1:
Inbound access-list is not set
Interface GigabitEthernet0/2:
Inbound access-list is macl_e1
Interface GigabitEthernet0/3:
Inbound access-list is not set
Interface GigabitEthernet0/4:
Inbound access-list is not set
<output truncated>
This is an example of output from the show mac access-group interface gigabitethernet0/1 command:
Switch# show mac access-group interface gigabitethernet0/1
Interface GigabitEthernet0/1:
Inbound access-list is macl_e1
interface interface-id (Optional) Display the MAC ACLs configured on a specific interface. Valid
interfaces are physical ports and port channels; the port-channel range is 1
to 48 (available only in privileged EXEC mode).
| begin (Optional) Display begins with the line that matches the expression.
| exclude (Optional) Display excludes lines that match the expression.
| include (Optional) Display includes lines that match the specified expression.
expression Expression in the output to use as a reference point.
Release Modification
12.1(19)EA1 This command was introduced.

Cisco WS-C3560E-24PD-E Specifications

General

Brand	Cisco
Model	WS-C3560E-24PD-E
Category	Switch
Language	English

Summary

Preface

Audience

Defines the target audience for the Cisco IOS CLI and switch software features.

Purpose

Describes the information about Layer 2 and Layer 3 commands for Catalyst 3560 switches.

Conventions

Explains text and symbol conventions used to convey instructions and information.

Related Publications

Lists related Cisco documents available from Cisco.com.

Obtaining Documentation

Explains how to access Cisco documentation and literature from Cisco.com and other sources.

Cisco Product Security Overview

Provides information on Cisco's Security Vulnerability Policy and how to report security problems.

Obtaining Technical Assistance

Provides information on how to obtain 24-hour technical assistance from Cisco.

CHAPTER 1 Using the Command-Line Interface

CLI Command Modes

Describes the CLI command mode structure and lists the main command modes for the switch.

Commands Changed in Cisco IOS 12.2(20)SE

Lists commands with the same function but different syntax in software releases before Cisco IOS Release 12.2(20)SE.

CHAPTER 2 Catalyst 3560 Switch Cisco IOS Commands

aaa accounting dot1x

Enables AAA accounting and creates method lists for IEEE 802.1x sessions.

auto qos voip

Configures QoS for voice over IP (VoIP) within a QoS domain.

boot system

Specifies the Cisco IOS image to load during the next boot cycle.

channel-group

Assigns an Ethernet port to an EtherChannel group, or enables an EtherChannel mode.

clear ip arp inspection log

Clears the dynamic ARP inspection log buffer.

dot1x

Globally enables IEEE 802.1x. Use the no form to return to the default setting.

ip address

Sets an IP address for the Layer 2 switch or an IP address for each switch virtual interface (SVI) or routed port.

mls qos

Enables quality of service (QoS) for the entire switch.

spanning-tree mode

Enables per-VLAN spanning-tree plus (PVST+), rapid PVST+, or multiple spanning tree (MST).

switchport mode

Configures the VLAN membership mode of a port.

vlan (global configuration)

Adds a VLAN and enters config-vlan mode. Use the no form to delete the VLAN.

vtp (global configuration)

Sets or modifies the VLAN Trunking Protocol (VTP) configuration characteristics.

APPENDIX A Catalyst 3560 Switch Boot Loader Commands

boot

Loads and boots an executable image and enters the command-line interface.

copy

Copies a file from a source to a destination.

delete

Deletes one or more files from the specified file system.

dir

Displays a list of files and directories on the specified file system.

set

Sets or displays environment variables to control the boot loader or other software.

APPENDIX B Catalyst 3560 Switch Debug Commands

debug auto qos

Enables debugging of the automatic quality of service (auto-QoS) feature.

debug cluster

Enables debugging of cluster-specific events.

debug dot1x

Enables debugging of the 802.1x feature.

debug ip dhcp snooping

Enables debugging of DHCP snooping.

debug platform ip multicast

Enables debugging of IP multicast routing.

debug spanning-tree

Enables debugging of spanning-tree activities.

debug sw-vlan

Enables debugging of VLAN manager activities.

APPENDIX C Catalyst 3560 Switch Show Platform Commands

show platform acl

Displays platform-dependent access control list (ACL) manager information.

show platform configuration

Displays platform-dependent configuration-manager related information.

show platform ip multicast

Displays platform-dependent IP multicast tables and other information.

show platform mac-address-table

Displays platform-dependent MAC address table information.

show platform pm

Displays platform-dependent port-manager information.

show platform port-asic

Displays platform-dependent port ASIC register information.

show platform qos

Displays global quality of service (QoS) information.

show platform spanning-tree

Displays spanning-tree state synchronization information.