Sony MLS-X1 User Manual

126
To swap color 1 and color 2 in a color mix
Set the [Color Invert] button to the on state.
To set modifiers for a color mix pattern
You can press the [Pattern Adjust] button and set the
f
ollowing modifiers from the displayed menu.
When the [Key Wipe] button is selected in the [Mix
Pa
ttern] group, the Home > M/E-1 > Key1 > Transition >
Wipe menu (11101.52) is recalled.
When the [Key Edge Pattern] button is selected in the
[
Mix Pattern] group, the Home > M/E-1 > Key1 > Edge
> Matte Adjust menu (11101.22) is recalled.
Position:
Set the [Position] button to the on state and set the
p
arameters.
For details about setting parameters, see “Setting the
wipe pattern position (Position)” (page 158).
Multiplication:
Set the [Multi] button to the on state and set the
p
arameters.
For details about setting parameters, see
“Replicating a wipe pattern (Multi)” (page 159).
Aspect:
Set the [Aspect] button to the on state and set the
p
arameters.
For details about setting parameters, see “Setting the
aspect ratio of a wipe pattern (Aspect)” (page 159).
Rotation (angle):
Set the [Angle] button in the [Rotation] group to the
o
n state and set the parameters.
For details about setting parameters, see “Rotating a
wipe pattern (Rotation)” (page 158).
Rotation (speed):
Set the [Speed] button in the [Rotation] group to the
o
n state and set the parameters.
For details about setting parameters, see “Rotating a
wipe pattern (Rotation)” (page 158).
Selecting the key fill/key source signals
You can select a key fill signal and a key source signal in
the menu.
For details about selecting a signal in the cross-point
con
trol block, see “Selecting a Key Fill Signal/Key
Source Signal” (page 91) and “Selecting a Video Signal/
Key Signal” (page 91).
To select a key fill signal
1 Open the Home > M/E-1 > Key1 > Type > Signal
Select menu (11101.14).
2 Press the [Edit] button for [Fill].
The [Key Fill Bus] window appears.
3 Set the button for the target video signal to the on
state.
Select a tab to change the cross-point button number
to
display.
4 Press [OK].
To select a key source signal
When the key source signal is set to split mode, select a
key so
urce signal.
1 Open the Home > M/E-1 > Key1 > Type > Signal
Select menu (11101.14).
2 Press the [Source Type] button for [Source], and
select video signal/key signal from the pull-down list.
Video: Vi
deo signal
Key: Key
signal
3 Press the [Edit] button for [Source].
The [Key Source Bus] window appears.
4 Set the button for the target video signal/key signal to
the on state.
Select a tab to change the cross-point button number
to
display.
5 Press [OK].
Selecting Signals (Key Control
Block)
Setting a key fill/key source
Select the target key to set and press the page selection
button to display page 2/3 of the setting buttons.
Set the signals to insert in the key fill and key source using
th
e key fill/key source selection buttons.
1 Set the key fill signal using the [MAT FILL] button.
To set a color matte
Press the [MAT FILL] button, turning it on green.
The parameters will vary depending on the menu
c
olor matte settings (single color or mix).
For details about setting a color matte, see “Setting a
key fill color mix” (page 125).
When single color is selected, set the following
p
arameters.

Sony MLS-X1 Specifications

General

Brand	Sony
Model	MLS-X1
Category	Switch
Language	English