326
[M/E-1] tab to [M/E-5] tab, [P/P] tab: Switcher
bank cross-point control block and transition
control block/transition control block (simple
type)/independent key transition control block
[Aux] tab: AU
X bus control block (ICP-X7000 only)
[Trackball] tab: Devi
ce control block (ICP-X1000
series only)
[Trackball/Key Fader] tab: Devi
ce control block
and key fader control block (ICP-X7000 only)
3
Select the target button to release.
To select and release multiple buttons, place a check
m
ark beside the target buttons to release.
To select and release all buttons, place a check mark
i
n the Select All checkbox.
4
Press the [Delete] button.
5
Check the message, then press [OK].
Releasing macro attachments on all
control blocks
1
Open the Home > Register > Macro > Attachment
menu (18307.31).
2
Press the [All Clear] button.
3
Check the message, then press [OK].
Executing a Macro Assigned in a
Macro Attachment
You can execute a macro assigned to a control panel
button or fader lever by enabling macro attachments.
• When set to multi mode, simultaneous execution of
mul
tiple macros is supported using the cross-point
buttons in the cross-point control block. Multi mode is
disabled if any other buttons or fader levers are
operated.
For details about multi mode, see “Executing multiple
macros simultaneously (multi mode)” (page 305).
• If the same button is pressed twice during macro
ex
ecution or when the macro is stopped, or if another
macro is recalled, the following operation depends on
the settings.
For details about settings, see “Setting the Macro
Mode” (page 421).
• Events registered in a macro are executed according to
t
he setup and the device configuration in force when the
events were registered. If the state has changed since
registration, the contents of the macro may not be
reproduced correctly when the macro is recalled.
• When executing a macro, if you switch to macro edit
mode,
the macro currently being executed stops.
• When creating/editing a macro, pressing a button or
fader l
ever for which a macro attachment is set does not
execute the macro.
Enabling macro attachments
You can enable/disable macro attachments using the
following buttons.
To enable macro attachments assigned on a
co
ntrol block of a switcher bank
Press the one of the following buttons, turning it on, in the
ta
rget switcher bank.
• ICP-X7000: [MACRO ATTACH ENABLE] button
assi
gned to the cross-point pad in the cross-point
control block
• ICP-X1000 series: [MCRO ATTCH ENBL] button
assi
gned to the function button section in the cross-
point control block
To disable, press the [MACRO ATTACH ENABLE]
but
ton/[MCRO ATTCH ENBL] button, turning it off.
To enable macro attachments assigned on a
co
ntrol block separate from a switcher bank
Enable using the following buttons assigned with the
“
Macro Attachment Enbl” utility command.
• Press a memory recall button in the utility/shotbox
cont
rol block, turning it on orange.
To disable, press the button, turning it on dark blue.
• Press a memory recall button in the utility control
bl
ock, turning it on orange.
To disable, press the button, turning it on dark blue.
• Press a cross-point button in the cross-point control
bl
ock, turning it on amber.
To disable, press the button, turning it off.
You can also permanently enable or disable macro
at
tachments.
For details about settings, see “Setting the macro
attachment enable/disable configuration mode”
(page 422).
Executing a macro assigned to a button
When macro attachments are enabled, the cross-point
buttons in a cross-point control block for which a macro
attachment is set are lit green. You can also configure a
setting so the buttons do not light up.
Notes
Note
Note
To Next Page
Loading...
Need help?
General
