189
For details, see “Properties display” (page 350).
Selecting a clip player output channel
Use the menu for the target clip player output channel for
operation.
When clip player output channel 1 (Clip 1) or clip player
ou
tput channel 2 (Clip 2) is selected, open the following
menu.
To recall video content:
Open the Home > Clip Player > Clip1/Clip2 > Clip >
R
ecall menu (14101.11).
The odd-numbered clip player output channel (Clip
1
) is shown on the upper left, and the even-numbered
clip player output channel (Clip 2) is shown on the
lower left. Content can be displayed in list view or
thumbnail view on the right.
For combined channels, the combined clip player
o
utput channels (Clip 1/Clip 2) are shown on the left.
To play video content:
Home > Clip Player > Clip1/Clip2 > Clip > Play
men
u (14101.12).
Information and operation buttons for the odd-
n
umbered clip player output channel (Clip 1) are
shown at the top, and information and operation
buttons for the even-numbered clip player output
channel (Clip 2) are shown at the bottom.
For combined channels, information and operation
b
uttons for the combined clip player output channels
(Clip 1/Clip 2) are shown.
Combining clip player output channels
Enable group mode.
This section describes combining Clip 1 and Clip 2 as an
e
xample.
1
Open the Home > Clip Player > Clip Common >
Channel > Config menu (14103.32).
The combine status is displayed for each clip player
o
utput channel.
2
Set the [ ] button between [Clip 1] and [Clip 2] to
the on state.
Group mode becomes enabled, Clip 1 and Clip 2
o
utput channels are combined, and a blue frame
appears. The clip player output channel display
changes to [Clip 1/Clip 2].
To uncombine, set the [ ] button to the off state.
To enable group mode using the clip player
ou
tput channel menu
Set the [Group Mode] button to the on state in the Home
>
Clip Player > Clip1/Clip2 > Clip > Recall menu
(14101.11).
• Channels cannot be combined/uncombined in the
fol
lowing cases.
– When channels are locked
– When playing video
• If group mode is enabled while content is recalled on a
cl
ip player output channel, the following occurs.
– If content 1 of combined content is recalled on Clip 1
and
no content is recalled on Clip 2, the channels are
combined and content 2 corresponding to the
combined content on Clip 1 is recalled on Clip 2.
– If content 1 of combined content is recalled on Clip 1
and
other content is recalled on Clip 2, a message
appears. If you press [OK], the content recalled on
Clip 2 is released, the channels are combined and
content 2 corresponding to the combined content on
Clip 1 is recalled on Clip 2.
– In all other cases, when content is recalled on Clip 1
or
Clip 2, a message appears. If you press [OK], the
recalled content is released, the channels are
combined, and both Clip 1 and Clip 2 become black
signals.
• If group mode is disabled while combined content is
recal
led on Clip 1 and Clip 2, a message appears. If you
press [OK], the channels are uncombined, content 1 of
the combined content remains recalled on Clip 1,
content 2 recalled on Clip 2 is released, and Clip 2
becomes a black signal.
Locking clip player output channels
You can lock a clip player output channel when video
content is recalled on the clip player output channel.
The following operations are inhibited on a locked clip
pl
ayer output channel.
• Recalling content
• Enabling/disabling audio
The following operations are inhibited for content
recal
led on a locked clip player output channel.
• Unloading content
To lock Clip 1, set the [Output Lock] switch for [Clip 1]
to
the on state in the following menus.
• Home > Clip Player > Clip1/Clip2 > Clip > Recall
menu (
14101.11)
• Home > Clip Player > Clip1/Clip2 > Clip > Play menu
(
14101.12)
Clip Player Content Operations
For details about displaying and selecting content, see
“Content Operations” (page 348).
Notes
To Next Page
Loading...
Need help?
General
