Juniper JUNOS - NETWORK OPERATION GUIDE REV1 User Manual

Checking for CFEB Alarms ! 425
Chapter 32: Monitoring the CFEBs
box is not forwarding
Oct 8 00:29:02 clinton chassisd[4891]: CHASSISD_SHUTDOWN_NOTICE: Shutdown
reason: CFEB connection lost
Oct 8 00:29:02 clinton alarmd[4893]: Alarm set: CFEB color=RED, class=CHASSIS,
reason=CFEB not online, the box is not forwarding
What It Means The messages system log file records the time the failure or event occurred, the
severity level, a code, and a message description. You can also use the
show log
messages | match cfeb
command to see error messages that are generated when a
Control Board fails or is offline. Use this information to diagnose a Control Board
problem and to let the Juniper Networks Technical Assistance Center (JTAC) know
what error messages were generated and the router events that occurred before and
after the problem. For more information about system log messages, see the JUNOS
System Log Messages Reference.
Step 4: Display CFEB Error Messages in the Chassis Daemon Log File
Action To display CFEB error messages in the chassisd log file, use the following CLI
command:
user@host> show log chassisd | match cfeb
Sample Output user@host> show log chassisd | match cfeb
Apr 28 03:25:13 Resetting CFEB 0
Apr 28 03:25:26 send: red alarm set, device CFEB 0, reason CFEB Not Online
Apr 28 03:25:26 Resetting CFEB 0
Apr 28 03:25:27 CFEB 0 added
Apr 28 03:25:27 CHASSISD_SNMP_TRAP7: SNMP trap generated: FRU insertion (jnxFruC
ontentsIndex 6, jnxFruL1Index 1, jnxFruL2Index 0, jnxFruL3Index 0, jnxFruName
CFEB, jnxFruType 4, jnxFruSlot 1)
Apr 28 03:25:46 Resetting CFEB 0
Apr 28 03:28:42 send: red alarm set, device CFEB 0, reason CFEB Not Online
Apr 28 03:28:42 Resetting CFEB 0
Apr 28 03:28:43 CFEB 0 added
Apr 28 03:28:43 CHASSISD_SNMP_TRAP7: SNMP trap generated: FRU insertion (jnxFruC
ontentsIndex 6, jnxFruL1Index 1, jnxFruL2Index 0, jnxFruL3Index 0, jnxFruName
CFEB, jnxFruType 4, jnxFruSlot 1)
Apr 28 03:29:17 rcv reply: CFEB Restart
Apr 28 03:29:17 CHASSISD_SNMP_TRAP9: SNMP trap generated: FRU power on (jnxFruCo
ntentsIndex 6, jnxFruL1Index 1, jnxFruL2Index 0, jnxFruL3Index 0, jnxFruName
CFEB, jnxFruType 4, jnxFruSlot 1, jnxFruOfflineReason 2, jnxFruLastPowerOff
5526, jnxFruLastPowerOn 5526)
Apr 28 03:29:17 sending 1 queued messages to CFEB 0
Apr 28 03:29:17 missing ctm for CFEB 0 -- timerid 0x0, timerset 0
Apr 28 03:29:17 send: CFEB config cmd
Apr 28 03:29:17 send: set_boolean_cmd CFEB 0 setting debugmode off
Apr 28 03:29:17 send: set_boolean_cmd CFEB 0 setting coredump on
Apr 28 03:29:17 send: set_boolean_cmd CFEB 0 setting source-route on
Apr 28 03:29:17 send: set_boolean_cmd CFEB 0 setting mtu-check off
Apr 28 03:29:17 send: set_boolean_cmd CFEB 0 setting soft-restart on
Apr 28 03:29:17 send: set_boolean_cmd CFEB 0 setting pfeman-reconnect off
Apr 28 03:29:17 send: set_boolean_cmd CFEB 0 setting l2cache on
Apr 28 03:29:17 send: set_boolean_cmd CFEB 0 setting no-load-balancing-clone off
Apr 28 03:29:17 send: set_boolean_cmd CFEB 0 setting equal-weighted-mode off
Apr 28 03:29:17 send: set_boolean_cmd CFEB 0 setting ipv4-key-hash-L3 on
Apr 28 03:29:17 send: set_boolean_cmd CFEB 0 setting mpls-key-hash-2label off
Apr 28 03:29:27 send: red alarm clear, device CFEB 0, reason CFEB Not Online

Juniper JUNOS - NETWORK OPERATION GUIDE REV1 Specifications

General

Brand	Juniper
Model	JUNOS - NETWORK OPERATION GUIDE REV1
Category	Software
Language	English