•
2-6 Delivery Section Auxiliary Switch Panel
PRINT
I
coo~s
A II
Ill
X10
MACHINE
B
I
coo~
II
Ill
X10
c D E
~
f--0
EJ
/,,,,
=
DOD~
F
~
ODD~
CYCLE
~
SET
[§]
[QJJ
G
H
0
1
2 3 4
I
PRINT
I
~
~
G:::)
M
• •
5 6 7
8
9
,
..
k
&
A.
Print
counter
This shows the total number
of
sheets printed from
the initial operation. This counter counts each sheet
of
paper fed through the press whether
it
is printed
or
not.
B. Machine
counter
This shows the total number
of
the cylinder rotations.
C.
~
Paper
feed
jam
detector switch
(With
the
fail-safe function*)
This
is
the
ON/OFF
switch
of
the
paper
feed
jam
detector
which
stops
the
press
when
sheet
travel
trouble on the feeder board occurs.
OJ
(ON) ......
The
device will operate.
IQ]
(OFF) .....
The
device will
not
operate.
D.
~
Paper
feed
break
detector
switch
This is the
ON/OFF
switch
of
the paper feed break
detector
which
stops the
paper
feed
when
a
paper
feed break occurs.
OJ
(ON) ......
The
device will operate.
JQ]
(OFF) .....
The
device will
not
operate.
(Note) This switch is not equipped with the fail-safe
function*.
Be
sure to use the press with this
switch at the
OJ
position.
E.
~
Electronic
type
double
sheet
detector
switch (With
the
fail-safe function*)
When wanting to print on the porous paper, set this
switch at the
OJ
position once, and then set
it
at the
IQ]
position again
to
only use
the
mechanical
type
double sheet detector.
«NOTICE»
Be sure
to
use the mechanical type double sheet
detector when printing with the electronic type
double sheet detector switch
at
the
IQ]
position.
If
printing is done without the mechanical type
double sheet detector used, the press
may
be
damaged.
F.
~Blanket
jam
detector
switch
(With
the
fail-safe function*)
This
is
the
ON/OFF
switch
of
the
blanket
jam
detector that stops the press when a sheet
of
paper
jams
on
any
blanket
cylinder
on
the first unit
and
second unit.
OJ
(ON) ......
The
device will operate.
IQ]
(OFF) .....
The
device will
not
operate.
G. Cycle set
button
Use this when setting each process cycle during the
printing
or
when
doing
the
maintenance
and
inspection.
( • Operation Edition - 44, Maintenance Edition -
10)
H.
~
Oil
warning
reset
button
When
the oil
warning
lamp
lights
on
the delivery
section operation panel, lubricate the required places
on
the press, then push this button. The lamp will go
off.
I. Cycle set indication
panel
The
cycle number
of
each process and contents set
by
th9
cycle
set
button
(G)
are
indicated
by
the
symbols.
Cycle
number
Cycle process
and
symbol
0
JPR!NTJ
Set at this position when printing.
1
rftf
Wet cycle
of
the water form roller for
the metal plate printing mode
2
n
Inking cycle
3
0
Blanket cleaning cycle
••
Wet cycle
of
the water form roller for
4
~
the polyester plate or paper master
printing mode
8
tt
Only service technicians use this.
&
Set at this position when doing the
9
roller
and
cylinder
pressure
adjustment.
(Note) There are no functions for the cycle numbers from
5 to 7.
* : Fail-safe function
When turning
ON
the press power, each detector will
turn
ON
automatically so that the press will not be
damaged. When wanting to turn
OFF
the device, set
the switch at the
OJ
position once, and then set it at
the
IQ]
position again.
Chapter
2
Names
and
Functions
Introduction Edition- 23
To Next Page
Loading...
Need help?
General
